[johnmac11]

Re: LG WM1437BFD washing machine.

Hi Mark,

Send me a PM with your email address and I will send you some info.

John

[johnmac11]

Re: My bits are shrivelled.

I have came across a few Whirlpool condensors with the same problem over the years and Whirlpool blamed the oils in suntan lotion for the problem..

John

[johnmac11]

Re: Butler oven spares

Thanks Don,

I have tried calling them a few times last week and again this morning and the phone rings 3 or 4 times then cuts out. Are they still in business??

John

[johnmac11]

Re: DAEWOO FRSU20FAI PARTS REQ

Thanks Bob 😀

John

[johnmac11]

Re: lg WM-1080FHD washer bearings

Easy job and wont take too long to do. bearings and seal are in stock at CDSL but will cost you about £50 + VAT

John

[johnmac11]

Re: Cata ES60SS electric hob

Thanks Ian,

I assumed that the only difference would be the length of the wire but was a bit confused when I saw the prices on the Cata website the 17 and 18 inch ones cost £1.86, the 19 inch one costs £7.86 and the 20 inch one costs £2.98…

Must be a special machine the cuts the wire for the 19 inch ones 😆

John

[johnmac11]

Re: Whirlpool akz 195

The AKZ ovens do not have a conventional oven clock, the power on these ovens goes to the main board and is fed to the clock via a ribbon cable.

Take a look at this post hereand it might help you

John

[johnmac11]

Re: Fisher pakel drawer dishwasher dd603

It will be either the heater plate or the controller that is at fault but 99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the time it is a faulty heater plate.

This is one of those jobs that will take me 20 minutes at most to do but will take a lot longer when done for the first time. You can confirm if the heater plate is faulty by reisistance checking at the bottom right harness on the controller, the readings will be in the info that dave-m has offered to send you.

John

[johnmac11]

Re: Can anyone tell me if this drum is sealed

Yes, it has a sealed drum but the complete drum/Tub assembly can be bought for a reasonable price :eeek:CLICK HERE

I dont think you will be buying that pile of landfill…..

HTH

John

[johnmac11]

Re: TECNIK DW PART NUMBERS REQ

Thanks Mark,

I just tried to get the model on the Bosch website and got the model not found message then I logged into my account tried again and up comes the model!!

John

[johnmac11]

Re: Whirlpool ADG 7540 – Rattling Noise From Below

Applianceman2010 wrote:. Also ken the link for the clips didn’t work for me…..

Link now repaired

John

[johnmac11]

Re: WTA site down??

I use the same as you Jim, NTL 20 meg connection.

John

[johnmac11]

Re: WTA site down??

It is working for me now Jim, have you paid your subs :rotl:

John

[johnmac11]

Re: AWM8000 Whirlpool..F08

Hi Jim,

I had a look through all the manuals for the Dreamspace washers and cannot see a chart with resistance readings for the ntc on any of them but the reading you have looks to be in the normal range for all their other washers. If the appliance goes through the test program OK I would go with a faulty heater/ntc

John

[johnmac11]

Re: WTA site down??

I get a time out error as well.

I just noticed that in the web links under the heading trade organisations that there is no link to the WTA site and the word organisations in the heading is spelt wrong.

John

[Author]

Posts