johnnyj

Forum Replies Created

Viewing 15 posts - 481 through 495 (of 1,251 total)
1 2 3 … 32 33 34 … 82 83 84
  • Author
    Posts
  • November 22, 2011 at 7:16 pm in reply to: bosch waq28360 – chinesey? #362722
    johnnyj
    Participant

    Re: bosch waq28360 – chinesey?

    I’ve had four in the last month with sealed drums all just over 2 years old and requiring new drums, i used to reccomend Bosch but starting to doubt that now. JJ

    November 21, 2011 at 7:00 pm in reply to: NARDI FEA0614X Fan motor #364056
    johnnyj
    Participant

    Re: NARDI FEA0614X Fan motor

    Thanks again Jackal ive kept you busy tonight, JJ

    November 21, 2011 at 5:25 pm in reply to: LG Tumble drier RC8001B BE fault code #364037
    johnnyj
    Participant

    Re: LG Tumble drier RC8001B BE fault code

    Is that the door micro switch, what is the belt like to change on one of these never done or seen one JJ

    November 21, 2011 at 5:09 pm in reply to: LG F1402FDS6 Door seal #364035
    johnnyj
    Participant

    Re: LG F1402FDS6 Door seal

    thanks Jackal

    November 16, 2011 at 8:10 pm in reply to: Indesit IWDE12 – dryer fault help #363697
    johnnyj
    Participant

    Re: Indesit IWDE12 – dryer fault help

    ntc, jammed motor or duff board i would guess at the motor myself, can you not rig up a supply to the motor and see if it runs.

    November 16, 2011 at 8:05 pm in reply to: Hotpoint wf541 jumping #363755
    johnnyj
    Participant

    Re: Hotpoint wf541 jumping

    Was it on the wool wash? i’ve seen them jumping about the place if they use the woolen wash for normal washing, got my mum a nice one of them customer was that petrified of the machine she bought a new one and was throwing it out mum has had it about 3 years now and it has worked a treat, it was washing on the wool wash that had cused it.

    November 12, 2011 at 3:45 pm in reply to: ZKI245 Dryer problems #362814
    johnnyj
    Participant

    Re: ZKI245 Dryer problems

    Sorry Chris i keep forgetting that with these it has an E72 fault i assume is dryer ntc as E71 is the wash ntc, does anybody know the part n/o for it thanks jj

    November 12, 2011 at 7:47 am in reply to: hotpoint dw model lft114 #363335
    johnnyj
    Participant

    Re: hotpoint dw model lft114

    Had a few of the console boards causing this and as the guys say the wiring getting stuck in the insulation and breaking also.

    November 7, 2011 at 7:10 pm in reply to: Hotpoint BWM129 Dispenser Front #363174
    johnnyj
    Participant

    Re: Hotpoint BWM129 Dispenser Front

    Try Indesit!!!!!!

    November 7, 2011 at 4:37 pm in reply to: GDA(Hotpoint)BF41 #363192
    johnnyj
    Participant

    Re: GDA(Hotpoint)BF41

    Probly the resettable thermostat popped if it over suds, situated at the back right hand corner if you reset, it should work.

    November 4, 2011 at 6:42 pm in reply to: Hotpoint WF100 dead. #362998
    johnnyj
    Participant

    Re: Hotpoint WF100 dead.

    I’ve had a couple of duff console boards do this, i usualy plug in another similar boaard if i havent got correct one to confirm, J

    November 3, 2011 at 6:55 pm in reply to: ZKI245 Dryer problems #362812
    johnnyj
    Participant

    Re: ZKI245 Dryer problems

    Thing is it isnt coming up with an error code, this is what has got me stumped, JJ

    October 18, 2011 at 2:35 pm in reply to: FFA71P Warm Freezer ? #360404
    johnnyj
    Participant

    Re: FFA71P Warm Freezer ?

    System leak probly they are bad for leaks, they seem to think it is usualy from the anticondensation loop, bypassing it sometimes cures but you will get a recall for condensation.

    October 15, 2011 at 6:39 am in reply to: Creda T601CW Water bottle feeder #361434
    johnnyj
    Participant

    Re: Creda T601CW Water bottle feeder

    There used to be a part n/o for the valve only, but i cannot find it the part n/o for the o’ring is 9980504, if your realy stuck i have a tdc30 i could take the part of for you . j

    October 12, 2011 at 4:03 pm in reply to: ADP 8332 – F7 and F6 faults #361262
    johnnyj
    Participant

    Re: ADP 8332 – F7 and F6 faults

    I’ve had the wires breaking as they go through door to the base cause this,

  • Author
    Posts
Viewing 15 posts - 481 through 495 (of 1,251 total)
1 2 3 … 32 33 34 … 82 83 84