johnnyj

Forum Replies Created

Viewing 15 posts - 556 through 570 (of 1,251 total)
  • Author
    Posts
  • in reply to: Hotpoint WD440 #339916
    johnnyj
    Participant

    Re: Hotpoint WD440

    Thats the ser n/o 9 digits, 1st 3 relate year and month of manufacture yours was made in march 2007, jj

    in reply to: indesit wib111uk no rotation. #340002
    johnnyj
    Participant

    Re: indesit wib111uk no rotation.

    Its has an Arcadia module unlike most of the other machines when the brushes wear and the door locks but wont fill, these machines will fill and drain but wont do anything else when the brushes wear, i woud guess at brushes or belt.

    in reply to: Hotpoint WF series #338876
    johnnyj
    Participant

    Re: Hotpoint WF series

    Yes Jim the split drums spin clockwise and the welded spin anticlockwise, different motors in each, the boards are the same but have to be programmed for the correct type cheers JJ

    in reply to: FLAVEL ML10FRS #338862
    johnnyj
    Participant

    Re: FLAVEL ML10FRS

    cheers helo

    in reply to: Hotpoint TDC30P Condenser tumble dryer with water leak. #338445
    johnnyj
    Participant

    Re: Hotpoint TDC30P Condenser tumble dryer with water leak.

    you can get them leaking between the plastic duct that is siliconed and screwed onto the back panel, ive sometimes cured with silicon, if not its a bin job as part is obsolete.

    in reply to: Hotpoint WT960 Control Board Relay #337864
    johnnyj
    Participant

    Re: Hotpoint WT960 Control Board Relay

    I would check the heater first had loads going down to earth causing an F08 fault, usauly when they have been washing coins etc damages the heater.

    in reply to: Hotpoint Expert #337868
    johnnyj
    Participant

    Re: Hotpoint Expert

    50/50 could be press sw or module i’ve been lucky most of the time with a press sw.

    in reply to: BOSCH SGV43A03GB – AQUASTOP FAILED ? #337493
    johnnyj
    Participant

    Re: BOSCH SGV43A03GB – AQUASTOP FAILED ?

    Replace aqua stop a couple of times for this, jj

    in reply to: Teka HM5951 #337146
    johnnyj
    Participant

    Re: Teka HM5951

    Forget that post ive found the parts thanks anyway JJ

    in reply to: Those little Servis type modules in built under freezers #336995
    johnnyj
    Participant

    Re: Those little Servis type modules in built under freezers

    Masterpart were doing them for £28 plus vat about a month ago i bought 2 when i seen them at that price

    in reply to: Hotpoint Fridge Freezer Flashing #336006
    johnnyj
    Participant

    Re: Hotpoint Fridge Freezer Flashing

    Switch the 2 control knobs to the off position then sw them back on usualy clears it, jj

    in reply to: Hotpoint wd64 dryer toc keeps blowin #333731
    johnnyj
    Participant

    Re: Hotpoint wd64 dryer toc keeps blowin

    As Iadom says 99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} certain if it has an FHP motor you will find chaffed wiring where it is tied to the motor there was a mod later which increased the length of the spiral wrap to eliminate this, as a matter course i always check and insulate the harness on every call to one of these with an fhp motor, JJ

    in reply to: KG31V04GB/06 #334850
    johnnyj
    Participant

    Re: KG31V04GB/06

    Hi Paul do you know the part n/o for the mod JJ

    in reply to: hotpoint sy51x oven #334480
    johnnyj
    Participant

    Re: hotpoint sy51x oven

    It will be the cutout locatednext to the grill element terminals part n/o C00089573 the temp they cutout was at increased, the oven usual shuts down after 10 to 15 mins after sw on, JJ

    in reply to: Electrolux EW1200I #334060
    johnnyj
    Participant

    Re: Electrolux EW1200I

    Thanks guys, jj

Viewing 15 posts - 556 through 570 (of 1,251 total)