Forum Replies Created
-
Posts
-
Re: TECNIK 795 / NO POWER PROBLEM
hi
it sound like a module problem, there are many versions ranging from £64 to £83 plus vat
can we have the full number from the machine
the number should be stamped on the stainless steel at the top of the door just buy the door lock (very difficult to see)
is this a tecknic TKD795/2 or TDK795/3
it may be marked SE6TIE1GB/?? or SE6TIE2GB/?? instead of the tecknik numbers
linrew
Re: Bosch washer won’t drain – i’ve tried everything! help!
hi
bosch part number for pump is 144305
before purchasing a new pump remove the filter and run machine on drain while looking at the pump to see if it is working ( keep fingers out ).
if it is it making the sound you mention (quiet buzzing) the buzzing usually indicates it is trying to work and something is stopping it. have a good look at the impellor (white or green cross like thing) it is not uncommon for something to wrap aroud the back of it and jam it up (usually an elastic band or string), do not remove the impellor as they wil not go back on, you would have to strip the pump down to remove the string/elastic band.
linrew
Re: AWZ541 Whirlpool Tumble Dryer problem
hi
there is no reset switch on these machines
it has 3 stats on it and any one could have gone, as could the heater
if you are a novice as you say i would advise you call an engineer
linrew
Re: Bosch washing machine failing to empty
hi
spin + rinsing lights flashing mean pumping period greater than 6 mins
usually this is a blocked pump but you say you have checked the filter
double check the hoses to and from the pump just in case there is a blockage in them
when the machine sticks is it full of water or empty?
if it stops and it is empty it may be a pressure sensor problem, depending on your ability it may be worth calling en engineer.
linrew
Re: Bosch WFX 3267 F04 Error
hi
F04 is pumping out time greater than 6 mins
probably pump blocked
check pump and all pipes to/from pump
linrew
Re: CDA CW495
hi
my limited experience with these machines has been a leak from a hose connected to the circulation pump, this resulted in a new pump being fitted to cure the problem.
fortunatly most (if not all) of these machines come with a 5 year parts guarentee so the customer saved 120 quid.
they are basicly a whirlpool machine inside
give CDA a call and see if you can get your own engineer from this site to fix it or does it have to be a CDA engineer
linrew
Re: can anyone help me find a part for a very old fridge/fre
hi
no these are the ones i can find and they fit the fridge compressor but wont fit on the freezer compressor due to the bracket for the cover
the one that was on the machine was about the 1 inch by 1 inch by 1/4 inch and only had 2 pins that connect to the compressor ( 😳 but like an idiot i have lost it otherwise i would take a picture of it and post it here 😳 )
many thanks for looking though
andy
Re: Bosch Cooler ( electronic Control ) KGV 2604
hi
what exactly is the fault on this fridge/freezer
does it cool down to correct temp then switch off then not switch back on or not until it is at room temp
if it is then there is a modification (available from bosch 491415 ) that can be done to these to cure the problem
the same problem has been reported here before and basicly involves cutting some wires and joining them together to bypass the stat..read the instructions in the kit very very very carefully and :zap: UNPLUG THE MACHINE :zap: before attempting anything
linrew
Re: recommend a d/w?
hi
i have to agree with penguin 45
also have a look at siemens machines as some of these come with 5 year warranty
linrew
Re: Bosch Flood protection activated.
hi
one of the more likley places is the inlet valve
run the machine for about 20 mins then :zap: UNPLUG THE MACHINE :zap: but leave the water connected, then remove the side panels and then look at the valve inside the machine for a small drip (easier to see from the right hand side of the machine with a bright torch or you can remove the valve from the rear then look at it).
as for the blockages the one in the pressure chamber is the one to clean along with the hose from pressure chamber to the sump. the one at the top left is not really needed
and is it the switch that is broken or just the button
linrew
Re: Siemens Microwave HF24052GB – Instruction Manual
hi
the part number for the instruction book is 520292
as you had no luck with bsh try searching the net using the part number
linrew
Re: Bosch WFL 2450
hi
the end light flashing indicates not drained within 6 mins
this is usually the pump or the waste hose blocked but as you have changed the pump and checked the pipe we must now look at what tells it that it hasnt emptied
the water level is controlled buy a pressure switch but these are usually quite reliable so look for a blockage in the tube running to it
this is usually located buy removing the lid and is usually brown or black in colour with a black tube comming out of the bottom
remove the black tube and blow down the end to see if it is blocked
if not try the pressure bottle at the other end of the hose connected to the sump hose at the base of the tub as this is possibly blocked with gunge
as for the drum not turning the brushes are probably worn out as you suggest (they normally last 5-7 years with average use)
:zap: POWER OFF BEFORE REMOVING ANYTHING :zap:
linrew
Re: Siemens Siwamat 6102 Washing machine Error code 4
hi
error code 4 is motor not turning correctly
POWER OFF then remove motor and check brushes. (probably worn out)
linrew
Re: Bosch WFL 2450
hi
do you have the full model number ie wfl2450gb/01 or /04 and the FD number
the active light flashing indicates that it has taken too long to fill (i am looking at the test sequence as i write this) ie longer than 6 mins
check that there is enough water pressure going into the machine and that the machine isnt syphoning. although this machine should have a device to stop it syphoning.
as for the motor not turning can you hear the control module clicking when the drum should be turning? if you can it is probably the brushes that are worn out
linrew
