Forum Replies Created
-
Posts
-
Re: hoover HCA39FA thermistor position
check your inbox sent you 2 , think they are the same just renamed 🙂
messey job good luck .phil
Re: HOOVER WASHING MACHINE
Blocked pump will do it every time some of the core boards werent programed correctly . WONT TIME OUT so it trys to pump out till the triac burns out ..allegedly so i here on the grape vine .. but hay thats just my opinion….
Re: Fault Code Guide
Sorry kwatt not to step on any ones toes , the pdf file worked on my nokia n95 n96 and a sony eccison satio , ok i like me phones lol , as long as you pay for the pdf ,,, Portable Document Format from the adobe site all will be well , anyways it was only £12.50 not a big price to pay for on in the hand
valuable info on the move ..
hth any one
phil
also working on a full pdf of all the fault codes listed , goner try to get it in alphabetical order . now did i spell alphabetical rite , its a beaatch being dyslexic .. lolphil
Re: Fault Code Guide
well some one produced it and emailed to me . some one from here but danged iff i can remember who . lol well it saved me making one at the time will take a pic…
check this page 1 http://www.ukwhitegoods.co.uk/modules.p … topic&t=40has the same spelling mistakes lol
does stop at page 6 thow 🙂
Re: Fault Code Guide
I allready have the pdf white goods fault codes on me samsung galaxy
works a treat ..Re: FAGOR FU-6146IT
F01 Appliance has failed to fill
F02 Appliance has failed to drain
F03 Appliance has detected drum imbalance
F04 Door lock has failed to engage
F05 Temperature Sensor outside expected range
F06 Appliance has failed to heat
F07 Overflow Detected/Blocked Drain Pump
F08 Motor has failed to operate
FO9 Drum not turningRe: Candy W/Drier CDB 126-80 PCB fault?
ok guys you can shout me down for this one 🙁
the ntc can go low insulation trust me on this ive had 3 of them do it giving a
fault code , yes they are nylon or plastic , yes megger it , . ive seen it with my own 2 eyes ..hth helps phil
Re: A Picture Says A Thousand Words
18 years old i think from the date code ?
yup reconed it lol just a set of brushes 🙂
Re: Hoover Optima OPH714D fault codes f03 and f16
yep just change the heater and all will be well very common on these m/cs
Re: hoover dyn10146p washer
ERROR CODE MOST PROBABLE REASONS FOR THE ERROR CODE:
E:01 Defective Door Safety Lock Device and/or Triac on Power Module and/or
Wiring.
E:02
The Water Fill Phase was not completed within the designed limit time.
Defective Solenoid Valve, Pressostat, Water Fill Hose, Low Water Pressure in
the network and/or Wiring.
E:03 The Water Drain Phase was not completed within the designed limit time.
Clogged Filter, Drain Pump, Drain Hose, Wall Discharge and/or Wiring.
E:04 Several (3) interventions by the Anti-flood Safety Contact of Pressostat.
Solenoid Valve blocked opened, defective Pressostat and/or Wiring.
E:05 NTC Temperature Reading Probe opened or shorted and/or Wiring.
E:06 Counter of Interventions by the Anti-unbalancement System (MEM readable
only).
E:07 Defective Door Safety Lock Device (blocked closed) and/or Wiring.
E:08 Defective Tachometric Dynamo (opened or shorted) and/or Wiring.
E:09 Defective “Cuore” Power Module (damaged Motor’s TRIAC) and/or Wiring.
E:11 Open Circuit on NTC Probe for Drying and/or Wiring.
E:12 Open Circuit on Drying Module and/or Drying Heater and/or Wiring.
E:13 Defective “Cuore” Power Module and/or Wiring.
E:14 Missing Water Heating: defective NTC Probe and/or defective Water Heating
Element and/or Wiring.
E:15 Not Programmed “Cuore” Power Module.
E:16 Water Heating Element is short circuited or defective electrical insulation.
E:17 Wrong signal from Tachometric Dynamo.
E:18 Defective “Cuore” Power Module – Wiring – Wrong Network Frequency (with
Knob Programs Selector).
E:18 Power-ON Times Counter (with Soft Touch Programs Selector – see Technical
Note 015lb09).
Best regards.hsd to do a quick copy n paste got to go out
hth phil
