[maltheviking]

Re: Knickers cause Zanussi to flash?

Hi Martin

“black frillies” ooohh! to much info :rolls:

Have you checked the pressure switch’s/ pressure hose/ chamber etc also check the heater it may have got damaged ( megger for earth fault )
Mal

Edit, re-read your post, forget the above 😳

[maltheviking]

Re: hotpoint tdl30

kladave wrote:Hi all any suggestions on what adhesive to use when fixing the front bearing felt into position
thanks dave

The felt usually has a sticky tape attached (peel off the paper a bit at a time ) but it is a pain if you don’t get the old tape cleaned off, you could use “Debor” adhesive. 😉
M

[maltheviking]

Re: Indesit group parts info?

kwatt wrote:See, I never ever got this at all.

Can anyone and, I do mean anyone, explain to me why I have to pay for information to buy goods?

K.Because they think you have to much money Ken 😆 being a north of the borderer that is 😉

OK I don’t know the price of this Partsfinder but the Elux. TDS is very fair, they must put as much work into its development as Hotmerithingy. Do you get the slightest inclination that Indesit are grabbin barstewards? :rolls:

[maltheviking]

Re: Throw away job or what?

Don’t forget the government gets 17.5{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} vat of this lot plus the vat of everything else involved in manufacturing etc. 😥 oh and it keeps the British workforce fully employed 😆

[maltheviking]

Re: Whirlpool ADP 4404/5

gegsy wrote:Hi Mal
Just to add, the flowmeter unfortunately isn’t a spare 👿 You will have to purchase the whole water matrix :rolls: p/no 481241868147.

Greg
Thanks Greg

I have just spotted that, bit pricey though 😥 thanks for the praise for the avatar 😉 it has the desired effect 😆

[maltheviking]

Re: Whirlpool ADP 4404/5

DentedPorsche wrote:Flow meter is in the water matrix, reed switch and tiny circuit board. Bad connection is the most common problem.

Brian

Thanks Brian Thats clarified the confusion 😕 I though it was the reed switch on the metering tank, it must be operated by a magnet. I have checked the connections but will do so again and take a a flow meter with me (30 mile round trip)

Who dented your porsche then 😆

Mal

[maltheviking]

Re: Hotpoint Oven Mod BS41

iadom wrote:Latest version I have been sent is now not black but red.

Jim. I wonder how I am going to convice customers that black oven doors fixed with red silicon is the latest “must have “accessory or worse still on a “green ” oven 😆

[maltheviking]

Re: Hotpoint Oven Mod BS41

Would it be possible to use some of the black heatproof silicon that we use?

[maltheviking]

Re: More exciting news!!!

Ay, thats as good as it gets in Kendal 😆 apparently they still stand their dead up in the bus shelters 😆 annnnd the traffic lights are still a major attraction on a saturday night :rolls: Oh I forgot about the sheep 😆

[maltheviking]

Re: Bosch W/m WFD2073 creeking

Had this problem on a Bosch a couple of weeks back, it turned out that when it was installed the supplier adjusted the feet but did not tighten up the locking nuts. Have a look at these 😉

[maltheviking]

Re: Servis ‘contraption’

iadom wrote:Whenever I get a phone call that mentions Servis, I politely inform them that If my grandmother was still alive and lived next door with a faulty Servis machine I would not go and look at it. Then I pass them on to an ex Comet,ex Servis engineer who lives nearby. I never get a single call back from him but it gets then off my back. 8)

Jim. You have a wicked side Jim 😆

[maltheviking]

Re: Hotpoint Aqualtis

I lost my confidence in “Which” years ago , they did the top ten of washers. Tricity Bendix came top, Zanussi came bottom. Same machine 😕

[maltheviking]

Re: Miele T430 dryer

Hi Kentish

I have “nailed it down” to a faulty relay on the power board, the coil of the relay was o/c, I have repaired the relay and now the motor runs 🙂

I still need a copy of the wiring diag. if anyone can help please.

Mal

[maltheviking]

Re: Just for the record..ouch!!!

It’s been mentioned in different posts, buy a “Volt stick” lads and lasses, they work. 😉

[maltheviking]

Re: CREDA 48145 double electric oven

Bryan wrote:
Perhaps it`s an idea to get your customer to contact their electricity supplier or who ever was responsible for the power cuts/surges.
Sure your customer would have a strong case for recompense if there was a known problem with the supply at the time.It`s not totally uncommon for electronics to fail under these circumstances.

HTH

Bryan

Hi Bryan
In our area the supply company have an added clause to thier contracts saying that they will not be responsible for any domestic appliance failure 😥 and they stick to it.
I had three customers with failed compressors on their fridges, all the same type(Candy) and in the same area all from the same power cut. I even gave them each others names so they could have a collective “go” and a report from me. The supply company just laughed at them, must have good lawers 😥

[Author]

Posts