[Martin]

Re: Zanussi Configuration codes

Tubs wrote:Have lost TDS at moment ( usuall teething problems with new installation)

Have you got broadband Steve?…I could email the info right now???

[Martin]

Re: Stacked machines 🙁

leavemetogetonwithit wrote:Now I’m really beginning to feel like I’m catching up

Yes indeed, you are making great progress…. :wave:

[Martin]

Re: Wanted Cannon 151 (ancientauto de-luxe gas cooker) gas p

They are called “Burner Caps” and may still be available BUT I do need the full model number to be sure (151 is not recognised 🙁 )

Also the’re usually are 3 different sized burners on Cannon hobs (Large, Medium and 2 Small – total 4) is that the case here as well?

[Martin]

Re: Creda built-in oven

Model number Sir Harry please???

[Martin]

Re: For the record

[Martin]

Re: Place Your Bets

[Martin]

Re: Bosch SMS3042

Igg wrote:Is this likely to be the inlet solenoid itself

Very likely, but firstly check that the clear tube from the inlet valve has no water in it? New valve (Part No 091051) available by emailing spares@ukwhitegoods.co.uk or direct from http://www.bshappliancecare.co.uk

[Martin]

Re: Bosch WFF1200 interlock wiring

Seamy wrote:I’ve ordered up new interlock sw’, but wondered if it may have taken out timer as well?

I’ve never had probs with Interlocks on this model (yet) but the Control Unit does go pear-shaped 🙁 On the 2 occasions I’ve replaced them, both had burned board terminals/soldered plug in connectors!

Pull the Control Unit away and check the board side is the best way to confirm 😉

[Martin]

Re: Hotpoint tdc62

Frustrated wrote:Wife bought the dryer from COMET. APPARENTLY THEY HAVE A SITE THAT YOU BID FOR RETURNED GOODS. She will not be doing that again !

http://www.clearance-comet.co.uk/

[Martin]

Re: Embarassing Bosch question

Penguin45 wrote:I’m still turning them upside down

Using this technique…..

What about the Rinse aid liquid spilling into the control panel?
The weight of the loose door just dangling from the wiring harness?
Salt water pouring out of the reservoir?
The motor falling out of its rubber mounts on reassembly?

Here is the earlier thread on the subject you were looking for Mark :-

http://www.ukwhitegoods.co.uk/modules.p … 25&start=0

[Martin]

Re: Hotpoint tdc62

Electronic controlled machines after all are prone to this I’m afraid….Sorry I cannot advise on HOW TO REPAIR by the way…best get expert help as prevoius post 😉

[Martin]

Re: Wet washing

darasux wrote:Whilst water is being expelled from the drain, lots of ‘sloshing’ water can be heard from the depths of the machine

Clearly the pump needs close attention AND the hoses to it and from it!

Repairs@ if you are the least bit unsure of the way forward 🙂

[Martin]

Re: Watch out for this one…

John042 wrote:Why moderator Martin

Many have asked the same question :con:

…….DEDICATION is the answer, but let that be our secret…OK? 🙂

Your analogies will serve you well by the way, except perhaps you may consider sparing the poor Labrador in favour of zapping a Cat as their electrical potential is lower!!!! :rotfl:

[Martin]

Re: Hotpoint tdc62

Firstly check the filter is clear, the water tank is empty, the door is shut….If yes is the answer to all 3 then the machine needs expert attention (see below).

Could be a connection problem with the wiper contact?…TOC? etc etc….worth getting expert advise 😉

[Martin]

Re: AEG Lavamat 72600 Error CE

manic4surf wrote:Correct me if i’m wrong but it sounds like a motor related problem from previous threads

Your conclusion is correct and I seriously recommend you seek help by clicking the Repairs@ link below….

[Author]

Posts