Forum Replies Created
-
Posts
-
Re: Bosch Max WFL2800 Boiling
Kirk,
First of all I’m a bit puzzled with the model number as I and Bosch do not recognise it ❓
Secondly, on any of the later Bosch/Siemens range one cannot fill a machine on 90degrees then switch to 40 without first ‘resetting’ the programmer. If you did such a thing it would simply continue with the first option selected, namely a 90 deg cycle 🙁
Finally, replacing the heater/ntc assy was a good move and should have cured the fault but that’s only assuming the NTC plug/lead terminals to the Module were in order? It is (IMHO) not a known module fault, but who knows maybe with the lady screwing up the programme, anything is possible 😯
Did you check the air pressure chamber when you changed the heater I wonder ❗
Martin
Re: Electrolux and AEG hob product recall
Dave,
Shouldn’t you post the link in the ‘Public Forum’ as well?
Martin
Re: hoover A3628 doorlatch assy. wanted
Steve,
The ‘Door Interlock Assy’ is Part No: 09164138 (Cost around £30)
Martin
Re: Hair Cut
kheath wrote:the rest of you can fuck off 😆
Slap Heads unite….Rock on 8)
Yes they can can’t they Kevin, hairy gits! 😆 😆 😆
Martin
Re: Ariston Brushes
Wet floor,
First the good news….Motor Brushes ARE available for your old machine 🙂
Now the bad….there are several ‘different makes’ of motors fitted to that model (i.e. Selni,Zem,Indesco,Ceset and I.B.Mei + variants within those too) 🙁
The best option is to take a brush unit out and take it to your local spares supplier for an exact match ‘over the counter’ so to speak 😉 OR take a snapshot of it and email me a picture for ident and supply :tup:
Martin
Re: Bosch Maxx shredding belt
Washerdoctor,
You didn’t divulge the model number, which as you know is vital for full and frank assessment :lesson: However, on most recent models within the range they do have s-t-r-e-t-c-h belts fitted and unless you fit a stretch direct replacement (e.g. 264987) then it will fail pretty quickly, derail and strip 😉
Martin
Re: Tricity/Bendix AW1200W
Why did the pump burn out I wonder? Was it that the sump is blocked, ‘cos if the sump hose is blocked it will affect the air bell to pressure switch? ..thus no fill and go into default 💡
Got to be trouble in that department I would say 😉
Best of luck!
Martin
Re: Zanussi Condenser TC 470 not drying
Yeah the belt does often catapult off during start-up, I agree. But a much cheaper fix would have been for them to simply make both pulleys with deeper grooves, to stop them ‘derailing’ 😉
Martin
Re: UKW…The future?
kheath wrote:However, patience is the key and one rung at a time is always best.
Spot on Kevin, that’s one of my virtues 😉
…..and I did fall off a step-ladder whilst cutting the hedge a couple of weeks back 😳
kwatt wrote:That should shut him up for a bit! 😆
My lips are sealed…. at least until I fix my broken step-ladder 😆 😆
Martin
Re: Cheap waste hoses
Hell of a good price Dave, put me down for 10 (Sorry dont use too many 😯 ) but if it helps shift them for you, count me in :tup:
Martin
P.S Stick them in your car for next months meet… save postage 😉
Re: 30,000 Reasons To Quit
Mind you ( I bet) that’ll be just ONE engineer covering the WHOLE of Scotland INCLUDING the Highlands and Islands….Not only that but the entire product range…..Good luck mate 🙁
Martin
Re: Bosch Maxx Washing machine not agitating or spinning
Lucy,
As Dave intimated it is most likely the Motor Brushes have worn after 3 years useage 😉 . Easy and relatively cheap to get sorted no problem if you get a local independant engineer in to fix it 🙂
Martin
kwatt wrote:What are you on about?
D&G!!!
and the ‘knock on effect’ to insurance in this business?
Martin
Re: Indesit WE 16 UK Door Seal replacement
Andrew,
I think it may be tricky for you but anyway, the part number you need for the new seal is : C00064545. It may well be available via out “shop@” site in the navigation bar?
Any problems I suggest getting a local independant engineer to do it for you 🙂
Martin
