Forum Replies Created
-
Posts
-
Re: What Do You Want To See On Or Done By UKW?
Dave_Conway wrote:If Martin wants to tidy the public forums, I don’t see a problem with that at all.
I will have a scan and get back to you beforehand!
Martin
Re: What Do You Want To See On Or Done By UKW?
Dave_Conway wrote:I think putting any error codes in there entirety in the public forums may cause more trouble than it’s worth tbh.
No no Dave,
What I meant by that was, (and I have bugger all knowledge of Diplomats so this may be irrelavant) but to post those ‘Error Codes’ that are given in ‘The User Guide’ (assuming owners of Diplomats have such things?? – Hotpoints and Bosch etc do!) “Shut Door”, “Switch On”, “Filter Check” that sort of stuff. Not technical i.e. “PRC Time Out” “Fill Time Out” etc etc
Just for Joe Public to see and ease off the postings to find out fundimental stuff that’s all 😉
Martin
Re: Known Error Codes – Bosh automatic
bonzaco wrote:“3” in the time delay display.
Element duff Bonz 😉
Martin
P.S May have to move this post from ‘Error Codes’ now into Trade Tech Enquiries though OK?
Martin
Re: Indesit W123
This is possibly a tricky one to sort Toni 😉 only in as much as it (as you probably know) has a complete s/steel tub/drum assy that cannot be sorted but can only be replaced. 🙁 2 thoughts spring to mind here, The inner drum spigot has cracked 😕 or the inner drum is twisted?
Dunno mate other than that 😕
Martin
Re: What Do You Want To See On Or Done By UKW?
A ‘tidy up’ in places as it is a bit messy in parts for ‘Guests’ to view!
Diplomat error codes placing in the customer/visitor area to prevent the endless stream of queries day in day out!
I think the ‘spare parts’ enquiries to be a major money spinner for UKW as most that view want to DIY 😉 😉
Fine tuning the key word here I reckon 😉
Martin
Re: Don’t Fancy Hotpoint, How about Hoover…
I will just go for the “Hand Held Computer & Technical Support” and to hell with the job 😉
Wonder if they do Gas training as well though for 16.2K????
Martin
Re: New Moderators
Alex wrote:Excellent choice of both parties here.I know Martin somtimes writes an epistle at times, (no offence mate), but I can see he looks into and takes an active interest in all posts.
My epistle writing days are over Alex, you see before you now a ‘Moderator’ in every way, and hopefully many will benefit from my dedication to UKW 😉
Martin
Re: Ariston Margherita AWD12
A fault with the main electronic circuit board (Module) is the most likely fault. 🙁 Try ‘Resetting’ the programme a couple of times (i.e. Press and hold the start button for up to 5 seconds) in the hope it clears 🙂
MartinRe: Why do Customers ……….
Good Heavens!
Yes I remember the 3226 transit bars 🙁 Orangey Brown, one across the back of the drum the other along the side…crickey, two ‘ old codgers together’ 😆
I had a similar one, this time a Bendix LTA where they never removed the transit straps. 😥 Someone placed bolts and brackets and fixed them to the ‘enamelled’ side panels and through the wall of a ‘perfabricated EX WW2 bungalow’ and the whole side of the house fell away!
Martin
Re: Indesit WD10 problems
Furhan,
I think it is almost certainly a connection problem to the main Module ❓
Resetting will usually cure minor hiccups in the programme eprom but unless the connections are good to it, it cannot respond 😉 Take off all the module plugs and refit them and try again. Beyond that Merlonielectrowhatshisname will have to step in and get it sorted under guarantee 😉
Martin
Re: Hotpoint Advertise Franchises!
Jonah wrote:Leave well alone, but its just an opinion.
Dave,
Thanks for sharing that with us and your story bares out most if not all of the comments on this thread 😉
Martin
Re: Why do Customers ……….
eastlmark wrote:oh,Penguin I remember those motors well, would be sweet on wash then suddenly turn into a catherine wheel once the spin kicked in.
Brilliant piece of engineering too, with thousands still operating faultlessly. Bosch V449 and V454 to name but 2. The motor has even got an in-built thermal trip so it is very unlikely you will find one ‘burnt-out 🙂
Martin
Re: The UKW Subscriber Forum
Those ‘Field Service Engineers’ amongst us that have not yet considered subscribing to our group, can I urge you to do so 🙂 As Ken says “It is not a Kings ransom” to be part of it, but the benefits will be all apparent in the months ahead. 🙂
Give UKW your support and be ‘Better Informed’ as a result 😉
Martin
P.S. Do read Kens posting on the previous page first OK!
