Martin

Forum Replies Created

Viewing 15 posts - 3,091 through 3,105 (of 25,534 total)
  • Author
    Posts
  • in reply to: Neff S5453 – finding cause of my flooded base #425758
    Martin
    Participant

    Re: Neff S5453 – finding cause of my flooded base

    Remove and clean that ‘pressure chamber unit’ as well as the grey corrugated transfer pipe and all will be well again.

    in reply to: Bosch HBM43B150B Hinge snapped shut #425723
    Martin
    Participant

    Re: Bosch HBM43B150B Hinge snapped shut

    Yes :tup:

    in reply to: bosch wtc84100gb/04 no heat #425536
    Martin
    Participant

    Re: bosch wtc84100gb/04 no heat

    Bloody hell, what size sink do you have? If the condenser is so badly blocked with lint then only a jet washer will clear it. 😉

    in reply to: Washing machine – what’s the best deal? #425687
    Martin
    Participant

    Re: Washing machine – what’s the best deal?

    The WDA110 has an angled control panel, a fraction cheaper than the WDA100 after cash back, has the same spec but also has a 5 year warranty. So the choice obvious, WDA110 wins! 🙂

    in reply to: AEG L5480WD washer dryer #425678
    Martin
    Participant

    Re: AEG L5480WD washer dryer

    From the manual ……Ed8 = No tachometric signal from power fan. Wiring faulty, Power fan faulty or WD PCB faulty, Drying phase skipped. I tried emailing manual but file too big and my mailer says NO! 🙁

    in reply to: bulb in currys cuc50w12 #425591
    Martin
    Participant

    Re: bulb in currys cuc50w12

    Light switch sticking?

    in reply to: Bosch wfp3300gb01, E05 but… #425584
    Martin
    Participant

    Re: Bosch wfp3300gb01, E05 but…

    Ordinarily you need to replace the whole brush end housing (part no: 00496875) But many guys in the trade fit just the carbons with the copper tails and solder them on.

    in reply to: Baumatic oven rom600ss won’t heat up after power cut #425582
    Martin
    Participant

    Re: Baumatic oven rom600ss won’t heat up after power cut

    Have you set the clock first?

    in reply to: Miele part- where does it go? #425560
    Martin
    Participant

    Re: Miele part- where does it go?

    Looks like a circuit board anti-splash guard has fallen off due to vibration. Needs clipping back on. NOT something you can blame the engineer for. 😉

    in reply to: Washing machine motors #425410
    Martin
    Participant

    Re: Washing machine motors

    Far better the OP lump them in the back of his van and take them to the scrap merchant. Got to be a tenners worth there I would think? 😉

    in reply to: Bosch washing machine not rinsing properly #425292
    Martin
    Participant

    Re: Bosch washing machine not rinsing properly

    As I mentioned earlier, your Bosch is a very basic model and lacks the deep rinse facility on the more expensive models. That, I suggest, is a feature ideally suited to overcome your special needs. A feature I insist on the machine I own and use as a necessity.

    in reply to: Bosch washing machine not rinsing properly #425288
    Martin
    Participant

    Re: Bosch washing machine not rinsing properly

    Tom wrote:just seeing this post now.
    I’ve seen a case where detergent powder accidently got into the prewash section of the drawer as well as main wash compartment.

    That is virtually impossible to achieve with this machine as the main wash compartment is separated from the prewash compartment by the fabric conditioner section in the centre.

    On the assumption the user doesn’t throw powder liberally into the drawer without careful attention of the separate compartment all will be well and dosage not compromised.

    in reply to: bosch wtc84100gb/04 no heat #425533
    Martin
    Participant

    Re: bosch wtc84100gb/04 no heat

    Bosch and tech info don’t go together. No heat is either the NTC, TOC or module as a general rule, so it has to be one of them I would think.

    in reply to: band has come off #425310
    Martin
    Participant

    band has come off

    95{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of new machines have a removable panel sufficient at least to facilitate belt replacement. Though it’s true to say that belts normally last longer than most other components in the machine. 😉

    in reply to: Bosch SMS4472GB sticking in the wash cycle #424974
    Martin
    Participant

    Re: Bosch SMS4472GB sticking in the wash cycle

    😉

Viewing 15 posts - 3,091 through 3,105 (of 25,534 total)