Micky 32

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 279 total)
1 2 3 4 5 6 … 17 18 19
  • Author
    Posts
  • December 7, 2013 at 1:00 pm in reply to: Bosch WTV4104GB/01 vented dryer #405870
    Micky 32
    Participant

    Re: Bosch WTV4104GB/01 vented dryer

    Thanks Martin will try that.

    December 7, 2013 at 2:11 am in reply to: Bosch WTV4104GB/01 vented dryer #405868
    Micky 32
    Participant

    Re: Bosch WTV4104GB/01 vented dryer

    Martin wrote:Would that be a WTV74104GB/0/01 by any chance?

    my apologies for the typo, it is indeed a WTV74104GB/01

    September 26, 2012 at 9:08 pm in reply to: CIC324AK foamed in sensor #287199
    Micky 32
    Participant

    Re: CIC324AK foamed in sensor

    Can you send it to me please?

    August 1, 2012 at 9:18 pm in reply to: Bosch 2416 Lights flash #378826
    Micky 32
    Participant

    Re: Bosch 2416 Lights flash

    Have seen this happen a few times with this model. Usually a reset can cure it, try that? Then check motor is spinning ok because worn brushes can cause the lights to flash. Just can’t think at the moment which lights the brushes cause to flash.

    February 21, 2012 at 10:47 pm in reply to: Whirlpool 3RLBR8543JQ2 toploader #369192
    Micky 32
    Participant

    Re: Whirlpool 3RLBR8543JQ2 toploader

    Well it wasn’t the coupling, so must be the gear box? Is that a big/expensive job? Is it easy to swap one?

    February 20, 2012 at 12:52 pm in reply to: Whirlpool 3RLBR8543JQ2 toploader #369191
    Micky 32
    Participant

    Re: Whirlpool 3RLBR8543JQ2 toploader

    Thanks lads for the replies, will have one tomorrow and hopefully will sort it.

    January 11, 2012 at 10:45 pm in reply to: Zanussi IZ 12( i think not sure) Jetsystem #367034
    Micky 32
    Participant

    Re: Zanussi IZ 12( i think not sure) Jetsystem

    Thanks for the reply Steve, will check again tomorrow.

    January 11, 2012 at 10:43 pm in reply to: Bosch D/W impellor jug question #366750
    Micky 32
    Participant

    Re: Bosch D/W impellor jug question

    Yeah it’s actually a common fault on these.

    October 14, 2011 at 9:15 am in reply to: Whirlpool AWOD 5526 not spinning properly going tomorrow #361347
    Micky 32
    Participant

    Re: Whirlpool AWOD 5526 not spinning properly going tomorrow

    Check the pressure bottle isn’t clogged, they’re prone to this.

    October 8, 2011 at 9:40 pm in reply to: Electrolux ESI 6220 diswasher #360884
    Micky 32
    Participant

    Re: Electrolux ESI 6220 diswasher

    Anyone? Does anyone have a service manual for this machine?

    October 8, 2011 at 9:39 pm in reply to: bosch wae24260/gb/01 washer #360841
    Micky 32
    Participant

    Re: bosch wae24260/gb/01 washer

    Would a pressure switch cause no pump action though? I’m sure you checked the pump to see if it’s open circuit? I’m sure i came across one of these that when the pump was gone it wouldn’t fill either.

    September 9, 2011 at 1:12 am in reply to: Whirlpool ADG 6230 IX dishwasher #358515
    Micky 32
    Participant

    Re: Whirlpool ADG 6230 IX dishwasher

    Anyone come across this??

    August 2, 2011 at 5:40 pm in reply to: Bosch WLX24162GB/18 Pump or PCB? #356605
    Micky 32
    Participant

    Re: Bosch WLX24162GB/18 Pump or PCB?

    Might just need a reset, come across a few that done this for no reason. turn dial to 6 o clock position, hold spin speed button and turn one notch clockwise 7 o clock and keep holding spin button for 5 seconds or so and turn off and on.

    July 31, 2011 at 2:37 pm in reply to: Candy smart C 514 ( i think) washing machine #356004
    Micky 32
    Participant

    Re: Candy smart C 514 ( i think) washing machine

    Well it turned out it wasn’t the selector. I checked button and ribbon and it’s ok so has to be the board. I also came across an identicle machine with the exact same problem. Is this a common problem with these boards?

    July 29, 2011 at 10:26 pm in reply to: Beko washing machine #356433
    Micky 32
    Participant

    Re: Beko washing machine

    There was originally an intake problem low pressure but this is now on it and holding the start button won’t reset it. Is there any other procedure to reset this?

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 279 total)
1 2 3 4 5 6 … 17 18 19