[Muv]

Re: hotpoint wma44 wiring diagram

This should be ok for you…supplied to me by “Iadom” recently

Looking down on the back of the board from the top, working from right to left, its one plastic sheathed amp tag and one unsheathed amp tag, one white, square plug into selector switch, large conn block from motor/doorlock to X1, 6 pin block, valves to X5, blue/black, pump conn to X11, black/black, pressure switch to X9, red/red, ntc to X2 and if fitted the small conn to the facia variable controls to X4

Martin

[Muv]

Re: Miele W828 rinse light flashing.

Hi all

I repair quite a few of the EL200 boards myself, but have now got a EL200C board to repair..
On this board there is a extra relay underneath the one marked 6K1 in the picture a few posts up..
(The usual one that the contacts weld together in)

Anyone know what this is for?

Martin

[Muv]

Re: Hoover HNF 7167 timer sticking

Ok thanks for that martin, will check it out

Martin

[Muv]

Re: Hotpoint Aquarius WDF740 soap dispenser removal.

Look at diagram of the drawer on page 12 of user manual..you lift at number 1 And pull towards you at number 2

Martin

[Muv]

Re: Hotpoint Aquarius WDF740 soap dispenser removal.

Just checked what type you have.!
You open the drawer fully then slightly lift up underneath the rear of the drawer that is nearest the drawer housing, then it pulls out towards you leaving the front of the drawer in place.. A tad fiddly the first few times, but easy after then…

Martin

[Muv]

Re: Hotpoint Aquarius WDF740 soap dispenser removal.

Oh sorry, my mistake..you just need to get the soap drawer out…
Should be a small tab at rear of drawer,you press down on (i think)

Martin

[Muv]

Re: Hotpoint Aquarius WDF740 soap dispenser removal.

When you take the soap drawer out..have you removed the screws from the fromt of the soap drawer housing?

Martin

[Muv]

Re: JLBi WD1400

Motor brushes?

[Muv]

Re: Candy washer/dryer won’t work.

My apolagies…wasnt thinking when i posted that… Its been a very very long day..

Well spotted martin..

[Muv]

Re: Candy washer/dryer won’t work.

Next step is check it at the door interlock

Martin

[Muv]

Re: MIELE T294C

Does it work on a timed setting?

Martin

[Muv]

Re: MIELE T294C

My mistake.. They have a front and rear NTC

Book values are 140k at 20C & 10.6k at 85C. If the element, thermostat, rear/front NTC, & wiring are all in order then it poins in the direction of the standalone heater PCB Just over £120 i think!

Martin

[Muv]

Re: Candy washer/dryer won’t work.

When you say there is power going to the machine, where have you tested for this?

Martin

[Muv]

Re: MIELE T294C

Isnt it a one shot type ? 160 degrees..

Martin

[Muv]

Re: miele w149

Not sure of thenexact location of the switch, but if you look at the iner part of the door you should see some sort of locating lug on there, this is the part that locates in to the door locking switch..

Also worth checking that the drum is in the correct location, before closing the lid..
By that i mean that the drum access door is at the top..

As for the other flashing lights

Turn the power of at the machine
Turn dial to finish/end of programme
Turn machine back on
And then re select programme

If its still flashing..then its time to call a qualified engineer..

Martin

[Author]

Posts