[Muv]

Re: hoover hnf6167 not spinning

You say the brushes are ok…how long are they..? Can you post a pictue of them…
Seems strange that it worked ok after you removed/replaced them

Martin

[Muv]

Re: hoover hnf6167 not spinning

Check the carbon brushes in the motor

Martin

[Muv]

Re: Hotpoint Ultima WT940P__Noisy

If its noisy only on the spin cycle…its more than likely the drum bearings are starting to wear…

Try putting your finger at the 12 o clock position of the inner drum and lifting slightly..you may feel a bit of movement there…..

Martin

[Muv]

Re: Electrolux Powerlite 1800W DEAD

1: a break in the mains lead

2: worn carbons brushes in the motor (usually dependant on usage of machine)

3: if machine is fairly modern and has a gradual speed startup ( then its th circuit board )

Hope this helps

Martin

[Muv]

Re: Bosch WFL2066 washer

Does anyone have a Manual for this machine please… either original, or PDF

Thanks
Martin

[Muv]

Re: Miele w829 washing machine

Ok,will prob use a solder sucker or braid to aid removal of solder…

How about the waste hose on these machines, will a standard hose fit on.. The small pipe outlet ?Or is it a miele hose only…

Martin

[Muv]

Re: QUALTEX BOSCH PUMP

I dont ever use pattern parts.. if i can avoid it anymore, you only get comebacks on them, whether you fit yourself, or sell over the counter..and for the few £s you save yourself, or the customer…i personally dont think its worth the hassle…

Thats a few pints talking!

M

[Muv]

Re: Bosch WFL2066 washer

Sorted…
Dirty connector in motor plug!

M

[Muv]

Re: Putting Indesit wixe127 just on spin

Looking at the manual, you can select a rinse cycle, from the function butoons at top of display and then press start.. It should then spin..

Martin

[Muv]

Re: Altus ADSV6 Dryer belt

Thanks ken, think i have finally located it on connect now,it is indeed a beko!

Martin

[Muv]

Re: Putting Indesit wixe127 just on spin

Does it not have a spin only option?

Martin

[Muv]

Re: Bosch WFL2066 washer

Have now replaced all parts, apart from the NTC Harness, which is still lost in post!
Have put on to test, but cant get any motor action, will these machines fail to turn if the NTC is not connected…? Brushes are fine, machine worked ok before..

Thanks
Martin

[Muv]

Re: Miele w829 washing machine

leavemetogetonwithit wrote:

Muv wrote:
.

I think this is the older type where you swing open the whole front after removing the 10mm head bolts round the door seal front and undoing the screws at the bottom of the front panel. The whole fascia area stays in place on the swung out front panel and you can then see how to remove it.
Mike.

You were right mike..

Take the 3 bolts out from around door boot, then the 3 screws around soad drawer housing.. Then one at top right of machine..unclip at bottom left under drain flap… And it all swings out left to right..

Thermal fuse has blown and the motor relay… Few quid and it should work fine..

Martin

[Muv]

Re: Zanussi ZFL1023 temperature knob indicator

Seems to be an absolete part,hopefully someone on here may have a used one..

This is the part …if anyone can help ..

Martin

[Muv]

Re: Miele w829 washing machine

Lol, ok I have now switched off auto bloody correction on my ipad…
Hopefully should have fewer spelling mistakes from now on..

Anyway.. Thanks for the info about the whole front panel swinging out..
I shall also give that a try..

Getting at the brushes from underneath, was suprisingly easy, once i worked out how the back end of the motor came off..

Hopefully its the RK1 relay, as described by “incognito” in his post..

One thing is for sure, these machines are built like a tank, this one is 12 years old..and the bearings are like new on it…previous owner swears she has never had it looked at since she purchased it from new Oct 2000

Martin

[Author]

Posts