[Muv]

Re: Hoover Optima OPH614-80 Error code

Sounds like a faulty fill valve or pressure switch to me?

Martin

[Muv]

Re: Hoover Purepower, need to know name of part please

Thanks for the photos, as I thought those bits form part of the top motor housing cover..

The cover is available for around £10+ vat
And also available is the bag housing, which also gives you the bottom half of these half broken pieces.. All depends on if these pieces are off either side of the top cover, or one piece is from the top cover, and other one is from the bag housing

Bag housing, and motor cover together are around the £25 mark

Hope this helps

Martin

Have tried to post pictures but not been successful

[Muv]

Re: Hoover Purepower, need to know name of part please

Thanks for the photos, as I thought those bits form part of the top motor housing cover..

The cover is available for around £10+ vat
And also available is the bag housing, which also gives you the bottom half of these half broken pieces.. All depends on if these pieces are off either side of the top cover, or one piece is from the top cover, and other one is from the bag housing

Bag housing, and motor cover together are around the £25 mark

Hope this helps

Martin

Note to moderators…

Not sure if I am allowed to post these photos, if not please accept my apologies and remove

Martin

Mod edit: Removed images as per edit in your previous post.

Don

[Muv]

Re: Indesit door boots in general

Thanks jem…

Once I looked at the pictures of the clamps, it all fell in to place… Going to fit a new spring tomorrow, as I was not happy with the tension on the spring after I struggled with it!…

Using your method I think it should be a lot easier

Martin

[Muv]

Re: Hoover Purepower, need to know name of part please

Yes, I thought it maybe the trunion ring, but these are made of a very flexible plastic, which don’t often,if ever! Break

I now think it the end pieces of the top,and bottom, motor cover, which locate at the sides of the main brush head housing and the handle swivels on these. ( if that makes sense )

Indesition… Any chance you can take a picture?

Martin

[Muv]

Re: Hoover Purepower, need to know name of part please

Yes, I thought it may be the trunion ring

Now I’m inclined to think its actually a part of the top motor housing, wich forms part of the swivel mechanism…

Any chance you can take a photo of the part?

Martin

Mod edit: Image deleted as it is a Connect copyright picture.

Don

[Muv]

Re: Hoover VHV 380 – 80 Tumble Dryer

Could be motor capacitor?

[Muv]

Re: Hoover Purepower, need to know name of part please

I think this is the piece that fits around the outer motor housing and then a large clip is screwed over this part on to the bottom chassis…. Usually the handle part of machine moves from side to side. …hence why the belt slips off..

Will try to post pic of said part

Martin

[Muv]

Re: Kenwood KDW243A/A

Had a few of these where the motor seems to check out ok..but have put another one in and machine worked fine…and a few with dodgy module…

Martin

[Muv]

Re: Hotpoint SDW60 (D/W)

PM me If you need the service manual…

Martin

[Muv]

Re: Hotpoint SDW60 (D/W)

Thats a heating circuit fault

Element,relay,wiring,module

Martin

[Muv]

Re: Hotpoint FDF 780 dishwasher (dish waster)!

Thanks to you both for your help

Martin

[Muv]

Re: Hotpoint FDF 780 dishwasher (dish waster)!

Yes that seems to be the problem, it’s coil is getting the correct voltage.. But it’s struggling to turn the impeller, although it is fairly free to turn by hand?

Martin

[Muv]

Re: Hotpoint TDC62

Update:

Job done!
Thanks again

Martin

[Muv]

Re: Hotpoint TDC62

Yes! Think I’ll be sweating like a gold diggers donkey doing it in this weather!

[Author]

Posts