Forum Replies Created
-
Posts
-
Re: bosch wae24162uk/01
Had same problem a couple of weeks ago, on that one it was a broken wire where the wire enters the motor plug.
Dead easy to check on these as the motor plug will prise apart to expose the connections.
Re: FAGOR FUS3611 IT
Got one myself to do, this one has timer problems ie. 2 min pump lasting 5 seconds.
Not located spares source yet, have you had any luck?
Neil
Re: Samsung Q1433S Door Handle
Thanks for that..
Problem was the bits were rattling about inside door frame so I never actually seen one assembled.
Anyone got a picture?
Re: Lucrative Dishwasher Money going west
steve wrote
I would seriously recommend one of these
Would not this course of action possibly lead to further complications 😯
I might just persevere though and restore this machine to as new condition even if I have to rebuild it from scratch. This particular model looks good if nothing else!
Re: Lucrative Dishwasher Money going west
Further to my Dishwasher Training Schedule I have now obtained this most highly esteemed dishwasher for spares or repair.
The fault as observed by myself is the machine will pump out on start up occasionaly but more often than not it just refuses to start.
On inspection I have found a build up of crud around the wash pump motor as shown on this picture available at
http://www.wellbebo.co.uk/Is this likely to be causing the problem?
How is this particular problem (leak) repaired?Thanks in advance..
Neil
Model Kenwood KDW12ssRe: Viewing UKWG web pages
Just changed it to 1440 x 900 and that has solved the problem.
Thanks Ken for pointer.
Neil
Re: servis tumble dryer start switch repair m2005w
Thanks Geoff,
Twas indeed the resistor, got one off a scrap module.
Even let customer help me with soldering!Happy Days 😀
Neil
Re: Hoover Washing Machine – No Pump But no Fault codes
Thanks A1
Customer has now scrapped machine, so that will make a nice recon.
Might even try swopping the triac myself. 😀Re: Beko Condensor Dryer/Hand Shredder DRCS65w H
I think there was a screw somewhere holding either pump or cover?
Finally sorted this one out, I think we will see a far few of these as the pump looks very prone to rust and seize up.
The whole job can be easily done through the inspection plate hole. The one thing to look for is a small philips screw on the top cover of the pump housing. Once that is out the cover unclips easily and the pump just lifts out.
Beware of sharp edges around inspection hole cover!Re: Beko Condensor Dryer/Hand Shredder DRCS65w H
There are clips that I have found inaccessible. One at the far right end of the pump cover, one below the motor pulley on the inside edge of the cover. Maybe others I can’t see? I didn’t want to break the cover if I could help it, but did manage to break one of the retaining clips already. How do you get at those inaccessible clips?
Re: Hotpoint TVM562G
stats and cap sound good, but am not familiar with this model. I think these ones will be just coming out of warrantys etc.
wondered about start relay or module?
Re: Debor Glue
Glue Finger
The habit of spending hours casually picking remenants of Debor from one’s fingers is a well known side effect, and one that gives one the appearence of a nervous schoolchild awaiting 6 lashes outside the headmasters office.And Debor stuck on the work trousers and/or jacket giving the appearence of someone who has just crawled out of a skip!
Good stuff though to get you out of a sticky situation.. 😆
Re: Beko Door seal rubbing
Had this myself after fitting gen Beko seal.
On that occasion it was the seal making contact with the drum. I loosened off clip around seal and refastened it while holding the seal forward as much as possible to give it that tiny bit of clearence. Seemed to help and to be honest customer not the fussy type anyway.
Must be an issue with the Gen seal?
Neil
