Penguin45

Forum Replies Created

Viewing 15 posts - 17,281 through 17,295 (of 19,678 total)
1 2 3 … 1,152 1,153 1,154 … 1,310 1,311 1,312
  • Author
    Posts
  • August 9, 2005 at 6:51 pm in reply to: Belling Format 600X #144372
    Penguin45
    Participant

    Re: Belling Format 600X

    You have mail….. 😀

    Chris.

    August 9, 2005 at 6:38 pm in reply to: Otpoint WM64 wiring diagram. #144370
    Penguin45
    Participant

    Re: Otpoint WM64 wiring diagram.

    Just call me Fred….. hopeless with names……..
    Cheers,
    Chris.

    August 9, 2005 at 6:25 pm in reply to: Otpoint WM64 wiring diagram. #144367
    Penguin45
    Participant

    Re: Otpoint WM64 wiring diagram.

    Did you click Bills email button, Ian? 😆

    Chris.

    August 9, 2005 at 6:15 pm in reply to: New door glass required #144374
    Penguin45
    Participant

    Re: New door glass required

    Dave Conway will be able to advise you on this tomorrow.

    Regards,
    Penguin45.

    August 9, 2005 at 6:11 pm in reply to: margherita 2000 troubleshooting #128336
    Penguin45
    Participant

    Re: margherita 2000 troubleshooting

    Well done – not your fault then 😀 .

    Penguin45.

    August 9, 2005 at 4:23 pm in reply to: Servis M3114 #144363
    Penguin45
    Participant

    Re: Servis M3114

    518004300 is gen – It appears to be the standard straight through Merloni pump, so plenty of pattern ones to choose from. Masterpart SV5102 is particularly inexpensive 😀 .

    Cheers,
    Chris.

    August 9, 2005 at 3:54 pm in reply to: margherita 2000 troubleshooting #128334
    Penguin45
    Participant

    Re: margherita 2000 troubleshooting

    The fact that it is draining some water out proves that the pump is working. However, it should drain the drum completely within 30-40 seconds. It implies that there is still some sort of blockage somewhere.

    Possibilities are choked coupling at sink (if that’s where the drain hose is connected to), crushed or kinked drain hose, sock or similar in tub to pump hose or a very tired drain pump just not spinning fast enough. The last may be identified if the pump makes a “drilling” or “burring” kind of noise.

    Power of please if you finish up going underneath it.

    Regards,
    Penguin45.

    August 9, 2005 at 3:43 pm in reply to: Indesit forno electric oven, grill ok but oven not heating #143703
    Penguin45
    Participant

    Re: Indesit forno electric oven, grill ok but oven not heati

    P/no is C00033977, selector switch. An email to spares@ukwhitegoods.co.uk will get things moving for you.

    Regards,
    Penguin45.

    August 9, 2005 at 3:20 pm in reply to: Zanussi WDT 1085 #144237
    Penguin45
    Participant

    Re: Zanussi WDT 1085

    Other possibilities are earth leakage through the motor or blown electronics. Both can give your machines symptons.

    Regards,
    Penguin45.

    August 9, 2005 at 2:49 pm in reply to: Blomberg 1301 ABB problem #144352
    Penguin45
    Participant

    Re: Blomberg 1301 ABB problem

    This is what you want:

    http://www.ukwhitegoods.co.uk/modules.p … t=blomberg

    Regards,
    Penguin45.

    August 9, 2005 at 1:05 pm in reply to: Bosch WET2820 washdryer #144346
    Penguin45
    Participant

    Re: Bosch WET2820 washdryer

    Had a couple of these with dodgy relays on powerboard, also fan motor not always cutting in (fluff, bearings or capacitor).

    Cheers,
    Chris.

    August 9, 2005 at 11:56 am in reply to: Smartdrive 051 drum fallen #144291
    Penguin45
    Participant

    Re: Smartdrive 051 drum fallen

    Fiona-Anne,
    The rods terminate in springs down at the tank bottom. At the top, they should be hooked into a kind of plastic corner piece. There are circular recesses around the tank base which the rods should slot into.

    Good luck, let us know how you get on.

    Regards,
    Penguin45.

    August 9, 2005 at 11:23 am in reply to: Hotpoint Mistral 8596 Fridge/Freezer #144335
    Penguin45
    Participant

    Re: Hotpoint Mistral 8596 Fridge/Freezer

    Kick strip – brown – p/no 2600695. An email to spares@ukwhitegoods.co.uk quoting the number should get things moving for you.

    Regards,
    Penguin45.

    August 9, 2005 at 11:19 am in reply to: Hotpoint Iced Diamond #144206
    Penguin45
    Participant

    Re: Hotpoint Iced Diamond

    Thermostat is p/no 261055 – an email to spares@ukwhitegoods.co.uk quoting that number will get things moving for you.

    Regards,
    Penguin45.

    August 9, 2005 at 10:11 am in reply to: BEKO WMA1715S #144307
    Penguin45
    Participant

    Re: BEKO WMA1715S

    Prewash blinks to indicate fault status Mike. If all components meter out, it has to be the power board itself. All the ones I’ve been to with this have turned out to be the PCB. P/no is 2810040110.

    Cheers,
    Chris.

    Edited due to inability to write a proper sentence in English!

  • Author
    Posts
Viewing 15 posts - 17,281 through 17,295 (of 19,678 total)
1 2 3 … 1,152 1,153 1,154 … 1,310 1,311 1,312