Phidom

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 1,873 total)
  • Author
    Posts
  • in reply to: Serviceforce guy from Somercoates? #317410
    Phidom
    Participant

    Re: Serviceforce guy from Somercoates?

    Is that where Batman lives? 😆 Well, it makes a change from penguin jokes.
    http://www.youtube.com/watch?v=l63SRpGXBHE

    in reply to: ariston a1237 #317398
    Phidom
    Participant

    Re: ariston a1237

    Check the brushes,fault code is for motor triac.

    in reply to: Ariston 1600 washer drier keeps throwing belt. #317336
    Phidom
    Participant

    Re: Ariston 1600 washer drier keeps throwing belt.

    Check the rear motor mounting on the tub. Perhaps the plastic bush is missing or the bracket is broken.

    in reply to: Hoover 148-80 #317313
    Phidom
    Participant

    Re: Hoover 148-80

    I think its 41001234.

    in reply to: They dont build em like that anymore – Part 20 #309245
    Phidom
    Participant

    Re: They dont build em like that anymore – Part 20

    Collecting washing machines? Now that is sad! :rolls: I had a Liberator machine that I used off and on until I broke it up 3 or 4 years ago but mine was the ordinary sort with wrap around cabinet. I still have the instruction book for it somewhere. Not very PC but quite entertaining with the ’70s fashion etc.

    Phidom
    Participant

    Re: AEG (In) Competence – C41022GM ( Grill & Heating Pro

    Presumably you are not hearing the fan working then?

    in reply to: Delonghi Fan oven not working #316999
    Phidom
    Participant

    Re: Delonghi Fan oven not working

    If there’s a timer on the cooker make sure it’s set to manual. It could be the thermostat but there are other possibilities like a burnt out wire somewhere. The thermostat operates like a switch so it’s continuity can be checked using a multimeter set to a low ohms range.

    in reply to: microwave buzing/humming confirm suspicions #316924
    Phidom
    Participant

    Re: microwave buzing/humming confirm suspicions

    No, I was probably confusing the issue there. The inverter microwaves don’t have the big capacitor and the magnetron wires go to a circuit board mounted in the base of the machine.

    in reply to: Hotpoint BWD20 Leaking at back of Drum #316184
    Phidom
    Participant

    Re: Hotpoint BWD20 Leaking at back of Drum

    I wonder if the leak could be from the joint where the bottom of the condenser meets the tub? You really need to run it with the back off and observe it leaking in operation.

    in reply to: microwave buzing/humming confirm suspicions #316922
    Phidom
    Participant

    Re: microwave buzing/humming confirm suspicions

    As the magnetron is a type of thermionic valve there is not much you can check on it with the meter, apart from the heater filament, which rarely fails. You therefore have to use the Sherlock method and eliminate everything else, leaving just the magnetron. You can check the capacitor, which will get charged by the multimeter battery and show increasing resistance until it goes to infinity. You can also check the primary and secondary resistances on the transformer. The diode will normally read open circuit in both directions on a normal multimeter but you can still check for shorts. There may also be a short circuit protection diode which can ironically also go short circuit. If the other parts check out OK you can be pretty certain the magnetron is cream crackered. On the other hand, if it’s an inverter type machine, that’s a whole different ball game!

    in reply to: triton shower #317011
    Phidom
    Participant

    Re: triton shower

    They usually have centre tap elements so perhaps one half has burnt out. My own Triton shower is not very warm just now but that’s because the incoming cold water is not much over freezing.

    in reply to: Now you can phone the moon! #316953
    Phidom
    Participant

    Re: Now you can phone the moon!

    That is amazingly cheap, I wonder how much a suitable phone would cost?
    Just remembered what date it is 😳

    in reply to: Hotpoint washing machine drum not moving #316932
    Phidom
    Participant

    Re: Hotpoint washing machine drum not moving

    Take the belt off and try turning it by hand again. It could be something stuck between the inner and outer drums, broken drum bearings or broken motor bearings.

    in reply to: Summer music festivals – anyone out and about??? #316576
    Phidom
    Participant

    Re: Summer music festivals – anyone out and about???

    Not been to any since I went to the last ever Stonehenge one in 1984. It was quite an experience though 😯

    in reply to: HPT new belt fitting tool #316871
    Phidom
    Participant

    Re: HPT new belt fitting tool

    Some useful tips there :tup: I did one the other week and made the mistake of taking the front off, quite a job getting everything lined up properly to get it back together.

Viewing 15 posts - 226 through 240 (of 1,873 total)