robwash

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 106 total)
1 2 3 … 6 7 8
  • Author
    Posts
  • February 18, 2009 at 6:23 pm in reply to: Smeg FAB40P frost free not defrosting #277731
    robwash
    Participant

    Re: Smeg FAB40P frost free not defrosting

    Any answer would be a great help please?

    November 20, 2008 at 5:57 pm in reply to: First Indesit smart card job completed #266425
    robwash
    Participant

    Re: First Indesit smart card job completed

    Hi, I’ve been bumping into a lot of Indesits lately with board problems. I’ve managed to sell a new machine to everyone luckily. Is it worth my while to buy a card reader and whatever else you need to sort these machines out. I have a whirlpool sam unit and they have decided not to update them. So that 200 sheets down the pan. It sounds like to me I may need to do some training on this. Can anyone give me some sound advice on this issue please?

    November 7, 2008 at 7:14 pm in reply to: Liebherr refidgeration spares??? #267670
    robwash
    Participant

    Re: Liebherr refidgeration spares???

    Thamks very much..looks like the credit card may come in handy

    November 6, 2008 at 8:15 pm in reply to: Whirlpool ADG6340 #267524
    robwash
    Participant

    Re: Whirlpool ADG6340

    i would say that it can only be the bontrol board unless the membrane switch (WI) in the sump is playing up

    September 29, 2008 at 4:03 pm in reply to: Leisure range oven CM10FRC. no right oven or food warmer #263191
    robwash
    Participant

    Re: Leisure range oven CM10FRC. no right oven or food warmer

    Thanks for reply but checked terminal block. Any help please

    August 3, 2008 at 6:53 pm in reply to: Whirlpool ADP8322 dishwasher #258811
    robwash
    Participant

    Re: Whirlpool ADP8322 dishwasher

    If you had a sam meter you can reprogramme control board and 9 times out of 10 the f7 will clear. If you change the flow meter it will definately clear the fault. I’ve never changed a valve for f7 but it could happen

    August 3, 2008 at 6:47 pm in reply to: Bosch F/F En-r KGV-3104-GB/04 #256805
    robwash
    Participant

    Re: Bosch F/F En-r KGV-3104-GB/04

    Have done the mod..it all comes on but the fridge doesn’t get below 7 degrees. Is this normal please?

    July 14, 2008 at 10:41 pm in reply to: Kenwood KCD1w TD #257708
    robwash
    Participant

    Re: Kenwood KCD1w TD

    Sounds like the drain pump has failed or blocked. I do a lot of these for leaking

    July 3, 2008 at 9:46 pm in reply to: Bosch F/F En-r KGV-3104-GB/04 #256802
    robwash
    Participant

    Re: Bosch F/F En-r KGV-3104-GB/04

    i understand. how does the fridge keep its temp? also the the plug for ntc is 3 way not 4??? cheers men anyway

    July 3, 2008 at 5:39 pm in reply to: Whirpool ADP 4400 dishwasher #256505
    robwash
    Participant

    Re: Whirpool ADP 4400 dishwasher

    fit the side chamber with flow meter. it is now the most common f11 fault.

    April 28, 2008 at 11:15 pm in reply to: Whirpool American F/F #250635
    robwash
    Participant

    Re: Whirpool American F/F

    CF is as porscheman says…comms failure. Change both boards. Only way to cure it properly.

    April 28, 2008 at 11:12 pm in reply to: whirlpool / servis w/m #250757
    robwash
    Participant

    Re: whirlpool / servis w/m

    All you can do is replace hose and try and tie back hose if possible

    April 28, 2008 at 11:09 pm in reply to: Samsung SR-S2028CSS NOT DEFROSTING #250612
    robwash
    Participant

    Re: Samsung SR-S2028CSS NOT DEFROSTING

    thankyou very much

    April 28, 2008 at 5:09 pm in reply to: Samsung SR-S2028CSS NOT DEFROSTING #250610
    robwash
    Participant

    Re: Samsung SR-S2028CSS NOT DEFROSTING

    I have only changed the heater. have you a part no. for the sensor please? many thanks

    April 7, 2008 at 5:40 pm in reply to: Whirlpool AWM8163 F8 error? #248230
    robwash
    Participant

    Re: Whirlpool AWM8163 F8 error?

    philguitar wrote:f8 is heater open regards phil
    🙂

    Phil’s a code and chord man!

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 106 total)
1 2 3 … 6 7 8