[scots]

Re: servis m3059 door handle

Try 719005000

Brian

[scots]

Re: Zanussi D/W no heat

But just imagine the relief when/if it works!!:)

[scots]

Re: Zanussi D/W no heat

Had the same problem with a Zanussi last week, cant remember exact model. After doing all the same tests you have done I bit the bullet and ordered the PCB and just in case also the NTC.
Result phew!!

Good luck with yours
Brian

[scots]

Re: belling farmhouse 910 grill regulator

Had a quick look on MP and confirm that it is now a Diamond H.
Seems most replace the Stix with Diamond H.
Having done, well lost count of how many, I have never had a problem.
Holes should be the same as Stix?

Brian
PS part number from MP = 082617129

[scots]

Re: homark grill regulator

Thermostat Nubmer is 76X3759
Checked Masterpart and they are £24.70

Sorry for late reply
Don’t seem to be getting informed of any replys?

Brian

[scots]

Re: homark grill regulator

Hi John

You sure this model has a regulator, thought it had just the oven thermostat to control temp and a switch to select oven/grill?

Brian

[scots]

Re: Whirlpool oven

Hi
Assume you mean AKP691 if so here are the elements

Grill oven element 481925928814
Base element 481925928847

Regards
Brian

[scots]

Re: Bosch dishwasher SGS532 GB17 module configuration

Hi
Did you get a copy, if not give me an email address and I will send you one

Brian

[scots]

Re: AEG 64840

Thanks for the reply Martin.

You make this test sound pretty common place, I haven’t found it. Could you point me in the right direction so I can thoroughly interogate the prisoner…

There is mention on here about continous pump but no answer to it.

Cheers
Brian

[scots]

Re: Hoover T2000 timer AC272

Hi
Really sorry for the late reply. This was my last job before a break in Prague (my wifes birthday present). I found one in some of my old Hoover updates.

Typical… I had stacks of Hoover manuals, did a clearout and guess what…

Thanks again

Brian

[scots]

Re: Indesit IDL40 UK.C Not Drying

I have replaced many boards on these machines due to not heating. Never seen any burning on the board tho.

I usually check heater circuit to make sure if this is ok then its the board, the new board comes with a new NTC.

Good luck
Brian

[scots]

Re: C6 reset on AEG 86741

Thanks for the info Seamy.

Machine now repaired, after eliminating all other possibilitys I bit the bullet a went for the board. EMW did there magic and now working a treat.

Just thought I’d let you know, maybe help someone else

Brian

[scots]

Re: Hotpoint DWF70S will not exit Demo.

Read on this forum 2 replies for this problem.

one said press reset for the 3 beeps then do the same for the on/off switch

the other one said press both on/off and start for 5 seconds.

I tried both without success.
I tried various combinations of holding start cancel button and on off until eventually display went to dOff. SORTED.

I think it was press and hold start cancel untill you get th 3 beeps, then press the same button as if you were resetting it again and hey presto.

Give it a try

Brian

[scots]

Re: Bosch Dryer WTL6300GB/01

Cheers Dave.

I have tried on timed although on these dryers the timed is a 20m gentle heat, not sure why but hey I didn’t design em.

Will try contact Bosch and see if they can give me any tech info on these dryers.

Thanks for reply
Brian

[scots]

Re: QER word of warning

We have had a few of this 75{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} charge with NFF, think its a bit exspensive.

The last one we got back last week, a Servis board, no spin.
Sheet attached says NFF but, they sent me back a different board with a number of wires soldered onto it and not to well ??

WHY if there is NFF did they not send the original board back?

I would stop using them now if I could but EMW (who are far better and more resonable) dont do a lot of boards.

[Author]

Posts