[Seamy]

Re: Miele F/L/A WS5426.. 1st rinse light flashing during spi

Rinse LED flashing means no signal received from tacho when motor should be running.
Normally its worn brushesbut can be cable loom, connections to motor or p.c.b or the p.c.b itself thats faulty.

[Seamy]

Re: Electrolux ERN 34800 display showing 0 error message

No evaporator sensor is listed as a replacement part, the appliance will default to factory settings if its faulty & use air sensor only.

You should be able to remove the fascia plastic cover carefully from front, think there are screws behind it to allow access to p.c.d.

Power OFF :lesson:

[Seamy]

Re: Talktalk what a joke!

Have they taken over AOL in the UK too?

[Seamy]

Re: Zanussi ZSF 6152 1 Flash fill error

Buzzing noise may perhaps be circulation pump motor trying to start, it may be stuck.

[Seamy]

Re: beko spares

Beko only do bearings in tub for WMA510 if thats the model??

Qualtex might do.

Genuine part num’s are–

Rear tub kit with bearings 2804200500
Carbon brush assembly 371201205

[Seamy]

Re: tricity bendix re60dcw timer bypass

Perhaps you should consider getting an engineer to check it out.
Its dangerous if you bypass the wrong thing, you say how the fan & light comes on as soon as switched on at wall, if element were to come on & heat when its not supposed to for instance because of faulty wiring there could be a dangerous situation.

[Seamy]

Re: Zanussi Electrolux F/F – Fridge warm and strange clickin

Faulty compressors can start sometimes & sometimes click out on thermal overload if they have overheated. Its hard to know what the clicking is without hearing it & inspecting the appliance. Fan in freezer could be catching on ice either, if this was the case a total defrost & start up could cure the problem. Could be a noisy defrost timer clicking either.
Compressor change is a specialist job & not to cheap to be honest.

[Seamy]

Re: Electrolux ERN 34800 display showing 0 error message

Control p.c.b is located behind the control panel at the top of appliance, tighten the connections to the edge of the p.c.b, this sometimes is all thats needed to cure it.
Some of the sensors are foamed into the walls of the appliance & are not changeable, (think this may be the case with yours) in this case the appliance defaults to factory settings & will continue to operate.
PNC or product code (9 digit num’) needed to confirm if sensors are changeable or not.

[Seamy]

Re: Beko WMA620W Door assembly does not fit

Its mentioned on the Beko technical website & shows graphic of different cut-out in the metal of front to accomodate changed support, can e-mail you info if you need it.

[Seamy]

Re: Aeg Washer Dryer, L12700VIT Prd 914601902

You need to be checking the cut-outs with the cables disconnected. Theres circuit diagrams on TDS

[Seamy]

Re: Beko WMA620W Door assembly does not fit

Hinge & support need to be changed together. If they don’t locate properly them its an old type front on the machine & this also needs to be changed.

[Seamy]

Re: AEG Santos fridge freezer problem

Sounds like its low on gas, or has a failing compressor.

[Seamy]

Re: Electrolux ERN 34800 display showing 0 error message

:lesson: UPLUG APPLIANCE, WHILE WORKING ON IT !

[Seamy]

Re: Zanussi Electrolux F/F – Fridge warm and strange clickin

May be a faulty motor compressor, if it clicks off a few seconds after the motor trys to start.

[Seamy]

Re: aeg l12510 vi flashes E30

E30s are pressure switch related, water level detection. Check the usual, pressure vessel & pipe for blockages, cabling to pressure sw’ & p.c.b, pump, filter, drain hose isn’t syphoning etc. Heater down to earth sometimes gives a E36 on some of these.

[Author]

Posts