[Seamy]

Re: AEG 86741>> Fabric softener problem

Try pulling out drawer slightly, fill with fabric conditioner as normal to below MaX level, then top up with water from kettle or jug to above the MaX level, conditioner should now all go through, if it doesn’t theres a blockage in the syphons or drawer, or that its not sitting in correctly.

[Seamy]

Re: aeg 72630 update – fixable ?

Pump faulty or blocked, hoses blocked perhaps. Open filter & drain water, see if it spins o.k then.

[Seamy]

Re: Miele G 679 Dishwasher

All lights lit means theres been a fault ( pump blocked ) in your case..

you now need to delete the fault code, think this is how you do it —

Open door& switch off-
Press & hold buttons 1 & 3 together
Switch on & release the buttons
Salt & programme button 2 will flash

Switch off

[Seamy]

Re: Bendix Flashes 5 times

E50 would be motor related, check brushes, earth short, burn’t armature, cable connections etc

[Seamy]

Re: Miele Dishwasher Codes & Test Pgm Needed

Check flow meter & cable connection at it & at board. Flow meter sometimes is not seated correctly & doesn’t pick up the impulses. If you think it fills to correct level but no circulation then wash pump may be blocked

PM me or e-mail me for fault code display info & i’ll scan something for you

[Seamy]

Re: AEG B8139-4-M

http://shop.aeg.co.uk/node13.aspx

[Seamy]

Re: Creda Aspire Solarplus cooker

try this for dowloading the instruction manual, you’ll need the model number

http://www.hotpointservice.co.uk/hs/pages/manual/manualSearch.do

[Seamy]

Re: AEG B8139-4-M Competence

timer unit 407 13 45-48 / 4,

http://shop.aeg.co.uk/node13.aspx

[Seamy]

Re: Creda T323 VW Tumble Dryer

Intake vents for air in machine base are usually the cause of poor air circulation, would advise to check that dryer is not heating on last 10 mins’ just in case the timer is at fault.

[Seamy]

Re: Electrolux END 5298 – fridge not working

PNC number would be of more benefit than model num’ as there are several models with different parts across the range, but the principle of appliance is that it cools the freezer section, a fan then circulates the cold air throughout the freezer & through a channel into fridge via a motorized flap aperature that opens & closes depending on what the settings are. Known problems are fans slowing up or seizing altogether, ice build-up preventing fan from turning, duct from freezer to fridge blockage, flap stuck closed. Freezer door switch being faulty would cause fan not to start also.
Any competant engineer should be able to suss it out quite quickly.

[Seamy]

Re: Lavamat 74620-W door problems

without being repetitive

try replacing the door switch first, its the cheapest option, test motor & heater for earth faults as they can throw up erroneous faults

[Seamy]

Re: zanussi washing machine beebing sound

Check filter & pump impellor for blockages.

[Seamy]

Re: Zanussi TC7102 dryer leaking

Check seals of condenser are clean & that condenser itself is not blocked. Theres a pump motor operated by a float switch that should come on when float switch is activated, they do stick sometimes though.

[Seamy]

Re: microwave capacitors

If its on the High Voltage side yes the size is critical to the output of the oven.

[Seamy]

Re: Miele Dishwasher Codes & Test Pgm Needed

Likely its got something blocked in the impellor of the was pump

[Author]

Posts