Seamy

Forum Replies Created

Viewing 15 posts - 2,266 through 2,280 (of 2,653 total)
  • Author
    Posts
  • in reply to: Miele G694SC plus 3 #224724
    Seamy
    Participant

    Re: Miele G694SC plus 3

    Check water in take 1st . Theres a float sw in base of this machine, to get access to machine take off top & sides. Check flowmeter (reed switch) you should wheel move around when its filling. Also check for level switch on curculation pump can give inlet fault too if it doesn’t register pressure.

    in reply to: miele w844 #223542
    Seamy
    Participant

    Re: miele w844

    If 10mm of water is not detected in 30secs “check inlet” is displayed, if no further increase is detected in next 30 sec’s drain pump is started.
    You can change this time from 60s to 255s in the programmable functions if theres bad water pressure.

    Check the solenoid valves, i think its a 3way cold water solenoid with a water protection system in built ( float switch in base ).
    Check filters are’nt blocked at water intake & also check pressure vessel for blockages too…

    in reply to: Terminal blocks #223427
    Seamy
    Participant

    Re: Terminal blocks

    Average load of hobs is 6kw thats presuming theres 2X 1800w & 2X 1200w plates, i know some have 1500 watt elements.
    A 6kw load would be take say- 27-28Aamp.
    Thats quesswork, not using any tables here, i know that 2.5mm T&E cable is capable of carrying 32A & 4mm is therfore OK for a hob installation.
    Most hobs have a short cable (a metre or so). The overheating problen arises from one problem mostly & you’ll find this whether the appliance is wired in 2.5mm or 25mm :- if the connections are not tightened then overheating occurs at the point of bad connection!

    in reply to: Hotpoint Ultima 1200 WM75 E15 Fault!! #223405
    Seamy
    Participant

    Re: Hotpoint Ultima 1200 WM75 E15 Fault!!

    Check pressure sw’ hose, pressures sw’ vessel, pressure switch etc.. sounds as if it may be emptying but pressure sw’ doesn’t recognise this.
    Also check cabling to motor, tacho coil etc.

    in reply to: Bosch WFG2029 GB filling all the time #223157
    Seamy
    Participant

    Re: Bosch WFG2029 GB filling all the time

    Thanks, it is a 2020, typing mistake , sorry…

    in reply to: Miele W821 Drain pump part 3568614 #222909
    Seamy
    Participant

    Re: Miele W821 Drain pump part 3568614

    ” RANSOM SPARES ”
    perhaps not the best business name in the world :rolls:

    in reply to: TDS Disc #222680
    Seamy
    Participant

    Re: TDS Disc

    Hi Alymer,
    if you deal with Quinnspares in Ireland they should be able to get one for you either.

    in reply to: The Open #222188
    Seamy
    Participant

    Re: The Open

    Well done Padraig Harrington, it was exciting & I never thought golf could be exciting..

    in reply to: Free energy #219590
    Seamy
    Participant

    Re: Free energy

    FREE energy is more dangerous than Saddam was to the developed world..
    What would happen to the the superpowers who spend trillions on oil & gas exploration & if two PADDIES could get a 275{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} efficient generator to work and make their technology available to the underdeveloped world for a next to nothing..

    But then again it could be the biggest IRISH JOKE ever 😆 ????

    Aren’t these the guys who invented the left handed screwdriver & the motorbike ashtray?

    in reply to: Miele H316B #221674
    Seamy
    Participant

    Re: Miele H316B

    Part number….5117406
    About £75 from Miele

    in reply to: miele t/dryer novatronic t454 #221340
    Seamy
    Participant

    Re: miele t/dryer novatronic t454

    Sensor for drum carbon brush is part num… 1454591
    Thermostats listed are
    100 degree stat….2911022
    120 degree stat….3226012

    in reply to: Power/Energy Monitor #221667
    Seamy
    Participant

    Re: Power/Energy Monitor

    Geat if the appliance is not hardwired to a fused, but most nowadays are.

    in reply to: Access Database for cust’s HELP !!! #221436
    Seamy
    Participant

    Re: Access Database for cust’s HELP !!!

    Its an awful big file to download my laptop threw in the towel & said not able to take any more…desktop crashed too…ooops

    in reply to: Access Database for cust’s HELP !!! #221433
    Seamy
    Participant

    Re: Access Database for cust’s HELP !!!

    Found this, it costs £95, try the free evaluation first

    http://www.accesstogo.org.uk/Service_Hi … nload.html

    in reply to: Access Database for cust’s HELP !!! #221430
    Seamy
    Participant

    Re: Access Database for cust’s HELP !!!

    i’m not so hot on it either but a template of some sort would be a major help,,

Viewing 15 posts - 2,266 through 2,280 (of 2,653 total)