Forum Replies Created
-
Posts
-
Re: ZANUSSI ZNB4051 – FRIDGE WARM, FREEZER TEMP FLUCTUATES
Reckon the fan is faulty or is catching on ice.
Re: wiring diagram AHY4120
Best to contact whoever supplied the part, we’re not supposed to give technical info out as its difficult to accertain the competance of the poster.
8/ Please do not ask for wiring diagrams, schematics or for us to sort out any wiring problems over the internet. We cannot judge how competent you are nor the future readers of any thread, we’ll try to point you in the right direction but that’s as far as we can legally go
Re: Ariston AV1247C – pressure switches engage but machine f
Might be worth checking theres not a small hole in pipe to pressure switch, it would keep filling as pressure would leak from hole in pressure tubing until high level was acheived then pump should operate.
Re: LIEBHERR F/F BOARD
Off topic a bit..
Any one have the cross reference of Liebherr to Miele parts, i’ve a Miele KFN8462 that gives F4 every now & again, reckon it needs Freezer NTC sensor. Think the Miele one is a tad expensive.Re: Connect deliveries
Had this problem years ago, stopped using them, they delivered parcels to wrong address constantly. When I rang abut not receiving parcels they said the same rubbish that driver had delivered to my address, even though my CCTV showed no delivery. A business 4 miles away from me got my deliveries several times & sent them back when driver next called. I E-mailed Connect regarding not getting parcels & never got a reply, I did’nt pay for stuff I didn’t get. They went to court & they won as the parcels were SIGNED FOR by driver obviously.
Re: Miele Heater Pressure Switch
Blowing in to it will not normally operate the switch unless you are an elephant. It needs high pressure, would’nt advise putting “similar”, used or s/h spares in any appliance.
Re: Stoves 720ef
You need to post long product number to be sure, Tecknik type Stoves oven has a regulator part num’ 936701900 listed..
Re: stoves hob
two parts shown, maybe superseded
081791600 & 08235100
see here..
http://www.espares.co.uk/part/cookers-a … witch.htmlRe: Zanussi w/m long pauses
simtoms wrote: although no fault codes come
If it didn’t drain in time it should give E21 fault, if pump was going out on o/l it would give fault code E23 or E24 if theres was a problem with triac supplying pump.
E32 can also show up during draining if electronic pressure switch senses water level descrapancies .I agree its likely its sticking at drain stage but in theory it should throw up a fault. Motor could be going out on high temp’ either which should throw up an E52 error.
Check error codes again, are you sure you are not deleting error codes without reading them.
Re: AEG 74630 OKO LAVAMAT Doesn’t complete programmes
Could be the water distributer sticking, ie- not getting to rinse position, or blocked pump, check if theres a coin in the impellor or stuck in a hose.
Re: Miele Heater Pressure Switch
The pressure switch needs quite high pressure to ativate it actually, its activated by the high water pressure when the circulation pump starts. After the appliance drains for a while it starts the circulation pump to check if theres water left or not, if pressure activates the switch it runs the drain pump a while longer. F11 can be a heater relay problem too but its generally a drain poblem.
Re: Stoves 1000EDL range cooker lower element
It might be a 0585600200… this element looks like it
Re: AEG PNC914524113 L74810 module configuration
You need a friendly Service Force engineer who has SideKick software on the laptop to configure the board, takes about a minute to do a P.C.B .
Just out of interest how much did the board cost?
There is very little difference of the configured & unconfigured boards listed on A.E.G/Lux website..“587 ELECTRONICS MODULE,NOT CONFIGU
(The part needs specific software and trained technicians for installation)
1 106.07
GBP 132 40 38-30/4
587 PCB,CONFIGURED,EWM1000+
1 104.93
GBP 9739 1452 41 13-00/3 “Re: electrolux esl45011
Two pressure switches on RHS one controls fill level, next is an overfill one that brings on pump & pumps out if appliance overfills. Theres a float switch in base also which would give similar symptons if theres was a leak. Look at fill matrix for gunge & try to clean out, or replace if its bad.
