superfix

Forum Replies Created

Viewing 15 posts - 796 through 810 (of 865 total)
  • Author
    Posts
  • in reply to: Hotpoint BS was it? #135819
    superfix
    Participant

    Re: Hotpoint BS was it?

    Let’s just hope it’s like the older SGS d/w range where our casing was used for the Hotpoint. 😕

    in reply to: Routeplanner/measuring tool #135883
    superfix
    Participant

    Re: Routeplanner/measuring tool

    kwatt wrote:

    boro wrote:
    Wish someone would send one to our office 😈

    Call centres… not a clue about geography (or much else in many cases ;)).

    K.

    How true 🙄

    in reply to: anyone for tenious? #135939
    superfix
    Participant

    Re: anyone for tenious?

    Wow Hosemartins I used to love them when I was lad

    in reply to: Routeplanner/measuring tool #135881
    superfix
    Participant

    Re: Routeplanner/measuring tool

    Wish someone would send one to our office 😈

    in reply to: Bosch Vacuum #135775
    superfix
    Participant

    Re: Bosch Vacuum

    Definately a broken wire from head s/w I’d say.

    We send them back to MK workshop for repair/replacement,as apparently they are pig to strip down any further. 😈

    in reply to: Scousers chances #135711
    superfix
    Participant

    Re: Scousers chances

    Zero chance now :rotl:

    in reply to: BOSCH WFB 2004 BEARING REPLACEMENT #135725
    superfix
    Participant

    Re: BOSCH WFB 2004 BEARING REPLACEMENT

    Oh dear 😉
    What a lovely job

    in reply to: Dear BSH-Man….. #135629
    superfix
    Participant

    Re: Dear BSH-Man…..

    In seven years of working for BSH I’ve never had a door lock blow a PCB.

    Honestly,it’s a new one on me. :con:

    In fact I could probably count on one hand the amount of door locks I’ve fitted.

    in reply to: Bosch Undercounter Oven/ceramic Hob HBN 200 T #135173
    superfix
    Participant

    Re: Bosch Undercounter Oven/ceramic Hob HBN 200 T

    There are no hinge carriers on this model 🙁

    So if door doesn’t close properly it’s usually scrap.

    in reply to: Neff Washer Dryer stopping mid -programme #135418
    superfix
    Participant

    Re: Neff Washer Dryer stopping mid -programme

    Could be a kinked inlet/outlet hose from whem m/c was pushed back after motor was fitted.

    in reply to: Bosch Undercounter Oven/ceramic Hob HBN 200 T #135169
    superfix
    Participant

    Re: Bosch Undercounter Oven/ceramic Hob HBN 200 T

    HBN200 series was the basic entry level appliance.

    Normally supplied by builders on new sites.

    in reply to: Bosch wfl2260 conditioner not being used #134171
    superfix
    Participant

    Re: Bosch wfl2260 conditioner not being used

    Martin wrote:Remove the drawer then clean the four holes in the dispenser cavity above the drawer. (They usually get blocked with a bacteria build-up!)

    Martin

    Poke a cable tie into the four holes in the middle of the dispenser.Then run through rinse cycle a few times.

    in reply to: Siemens D/Washer Identification Label Scrubbed Off #133624
    superfix
    Participant

    Re: Siemens D/Washer Identification Label Scrubbed Off

    Hey BSH MAN

    It’s the water in Hartlepool,supposedly the hardest water in Britain!!!

    Still ask for two units though 😉

    in reply to: Bosch KGU3120GB Freezer Problem #133717
    superfix
    Participant

    Re: Bosch KGU3120GB Freezer Problem

    Probably frozen evaporator.

    Turn off,leave for 24 hrs.Then try again.

    p.s. have plenty of old towels handy. 😉

    in reply to: Siemens D/Washer Identification Label Scrubbed Off #133622
    superfix
    Participant

    Re: Siemens D/Washer Identification Label Scrubbed Off

    Another (faster) way to change said heater.

    Remove right hand side panel.Front and rear tank screws and hinge spring.Lift r.h.s. away from base and fix in position.

    Now use side cutters to cut male lugs on existing heater,cut female locators on new heater.

    Hey presto fit new cartridge to old case.Done about ten this way now.20 to 25 minutes to complete job.

    This upside down methhod,no thanks.Far to messy.. :haier:

Viewing 15 posts - 796 through 810 (of 865 total)