TheSpinDoctor

Forum Replies Created

Viewing 15 posts - 151 through 165 (of 418 total)
1 2 3 … 10 11 12 … 26 27 28
  • Author
    Posts
  • March 9, 2010 at 4:42 pm in reply to: Zanussi ZWD12270w1 washing m/c #314423
    TheSpinDoctor
    Participant

    Re: Zanussi ZWD12270w1 washing m/c

    Hi

    I would change the main board 97391460 40 28-00 / 6 in conjunction with the door lock 124 03 49-01 / 7.

    March 9, 2010 at 4:40 pm in reply to: Zanussi ZWF1432W #314378
    TheSpinDoctor
    Participant

    Re: Zanussi ZWF1432W

    Hi.

    I assume you have tested for an insulation fault?

    March 9, 2010 at 4:30 pm in reply to: Zanussi ZJD1219 Dryer stops mid cycle #313962
    TheSpinDoctor
    Participant

    Re: Zanussi ZJD1219 Dryer stops mid cycle

    I suspect the condenser is not the issue here as when it blocks it will also usually display E20.

    Do you have a test meter that is able to test the isulation of the product? I suspect this may reveal a fault for you.

    March 9, 2010 at 4:27 pm in reply to: zanussi zwf1427w #314120
    TheSpinDoctor
    Participant

    Re: zanussi zwf1427w

    132 10 20-21 / 4 is what you require.

    March 9, 2010 at 4:24 pm in reply to: AEG 5410 oven no heat #314290
    TheSpinDoctor
    Participant

    Re: AEG 5410 oven no heat

    Check your PM’s mate.

    March 8, 2010 at 7:55 pm in reply to: Gauge manifold & hoses. #313336
    TheSpinDoctor
    Participant

    Re: Gauge manifold & hoses.

    Bob. Where are you?

    Speak to me. 😀

    March 8, 2010 at 7:53 pm in reply to: AEG 5410 oven no heat #314288
    TheSpinDoctor
    Participant

    Re: AEG 5410 oven no heat

    Hi.

    That model shows 18 versions. Do you have a product number please?

    March 8, 2010 at 7:43 pm in reply to: zanussi zwf1427w #314116
    TheSpinDoctor
    Participant

    Re: zanussi zwf1427w

    odom wrote:No water going in would cause machine to abort programme about two mins into wash.

    It would, but it would display E10 & not 0.

    March 8, 2010 at 5:39 pm in reply to: ZANUSSI ZWF12070W1 #314170
    TheSpinDoctor
    Participant

    Re: ZANUSSI ZWF12070W1

    Hi.

    I have had several lock issues recently but it all depends upon the type of lock used which I can only tell what one you have by the product number beginning 914 but unfortunately this is on the rating plate behind the now locked door. 👿

    March 8, 2010 at 5:35 pm in reply to: Zanussi 1397 spin/no spin problems #314236
    TheSpinDoctor
    Participant

    Re: Zanussi 1397 spin/no spin problems

    Hi.

    Things to check:

    Motor brushes.

    Air chamber.

    Loading.

    March 8, 2010 at 5:33 pm in reply to: Inner Glass for Oven door #313912
    TheSpinDoctor
    Participant

    Re: Inner Glass for Oven door

    Hi.

    Usually the glass takes a slight knock which can cause the glass to “bruise” which then can make it susceptable to thermal shock.

    March 8, 2010 at 5:27 pm in reply to: AEG Vented Dryer Fault #314212
    TheSpinDoctor
    Participant

    Re: AEG Vented Dryer Fault

    Hi.

    Check your PM’s mate.

    March 8, 2010 at 5:16 pm in reply to: Zanussi ZKT 641F #314080
    TheSpinDoctor
    Participant

    Re: Zanussi ZKT 641F

    Assuming that product number is correct then the electronic has a part number of 330 64 50-00 / 2.

    March 8, 2010 at 5:10 pm in reply to: zanussi zwf1427w #314114
    TheSpinDoctor
    Participant

    Re: zanussi zwf1427w

    If you have a suitable test meter, I would advise you test the appliance for insulation faults.

    March 7, 2010 at 10:46 am in reply to: Beko WMA510 Inner drum #314165
    TheSpinDoctor
    Participant

    Re: Beko WMA510 Inner drum

    Check your PM, Geoff.

    Happy reading.

  • Author
    Posts
Viewing 15 posts - 151 through 165 (of 418 total)
1 2 3 … 10 11 12 … 26 27 28