TheSpinDoctor

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 418 total)
1 2 3 … 14 15 16 … 26 27 28
  • Author
    Posts
  • January 6, 2010 at 6:04 pm in reply to: Beko WM7147W Motor #308054
    TheSpinDoctor
    Participant

    Re: Beko WM7147W Motor

    Hi.

    The part number you need is: 2826520100.

    Hope this helps.

    January 2, 2010 at 1:18 pm in reply to: Happy New Year! #307500
    TheSpinDoctor
    Participant

    Re: Happy New Year!

    I think he meant a Mill-yun-air.

    Bonee Da Douche!

    Have a good ‘un all.

    December 30, 2009 at 7:04 pm in reply to: AEG40850-DISHWASHER-SALT ISSUE #307413
    TheSpinDoctor
    Participant

    Re: AEG40850-DISHWASHER-SALT ISSUE

    Hi.

    I would suggest that you test the regeneration valve coil for resistance. If it is open circuit then there is your problem.

    December 27, 2009 at 6:35 pm in reply to: wont pump in but seems to pump out #307199
    TheSpinDoctor
    Participant

    Re: wont pump in but seems to pump out

    Hi.

    I assume that the drain pump is not running constantly. If so, you have a leak inside the machine. If not, check tap is turned on, inlet hose is not kinked or blocked & inlet valve coil is not open circuit.

    December 26, 2009 at 11:03 am in reply to: beko wm5120s #307172
    TheSpinDoctor
    Participant

    Re: beko wm5120s

    Hi.

    I have something that you may find of use but I cannot upload it on here. PM me your email addy & I will send it to you.

    December 25, 2009 at 2:28 pm in reply to: AEG L12700VIT Door locks and display blank. #307064
    TheSpinDoctor
    Participant

    Re: AEG L12700VIT Door locks and display blank.

    Hi.

    Two words.

    Board F**ked!

    Door lock may have caused it but theoretically can be caused by just about anything so your best bet is to take out the board & see where it is blown & trace the wiring back. Then you could also test the insulation of components as a belt & braces approach.

    December 24, 2009 at 9:14 pm in reply to: John Lewis JLDWS1202 Not Heating #307075
    TheSpinDoctor
    Participant

    Re: John Lewis JLDWS1202 Not Heating

    Hi.

    It may be a fault with the pressure switch itself.

    December 24, 2009 at 9:11 pm in reply to: Christmas Greetings!! #307145
    TheSpinDoctor
    Participant

    Re: Christmas Greetings!!

    Merry Christmas & a Happy New Year to one & all.

    Best wishes.

    December 21, 2009 at 8:09 pm in reply to: zanussi zsf 9126 dw #306964
    TheSpinDoctor
    Participant

    Re: zanussi zsf 9126 dw

    Hi.

    Most likely you have a leak inside the product which has triggered the flood protection switch.

    December 20, 2009 at 6:28 pm in reply to: Newworld #306917
    TheSpinDoctor
    Participant

    Re: Newworld

    Hi.

    Sounds like a potential energy regulator issue to me.

    December 20, 2009 at 10:10 am in reply to: Zanussi washer dryer tripping the RCD. #306514
    TheSpinDoctor
    Participant

    Re: Zanussi washer dryer tripping the RCD.

    You are most welcome.

    Merry Christmas.

    December 19, 2009 at 8:24 am in reply to: Zanussi washer dryer tripping the RCD. #306510
    TheSpinDoctor
    Participant

    Re: Zanussi washer dryer tripping the RCD.

    I would check the heater wiring connections, sump hose, drain filter & air chamber if I were you.

    December 18, 2009 at 7:10 pm in reply to: lime scale #306731
    TheSpinDoctor
    Participant

    Re: lime scale

    Hi.

    You might want to periodically run a cotton boil wash without laundry with half a measure of a quality brand biological powder based detergent & clean the filter afterwards.

    Worth a shot.

    December 18, 2009 at 6:57 pm in reply to: Zanussi washer dryer tripping the RCD. #306507
    TheSpinDoctor
    Participant

    Re: Zanussi washer dryer tripping the RCD.

    Hi.

    Cleaning the condenser would be well advised.

    December 18, 2009 at 6:56 pm in reply to: Zanussi IZ161S Not Operating Correctly #299203
    TheSpinDoctor
    Participant

    Re: Zanussi IZ161S Not Operating Correctly

    Hi.

    There is no part number from Electrolux Distriparts that exists for a triac. It is the board or nothing from them. Whether you can get it for Maplin or wherever, I don’t know.

  • Author
    Posts
Viewing 15 posts - 211 through 225 (of 418 total)
1 2 3 … 14 15 16 … 26 27 28