Forum Replies Created
-
Posts
-
Re: zannusi zwd16270w
E11 is a fill problem, E21 is drain problem. I cannot see how cleaning the filter would resolve a fill issue.
If it has, well done but let us know if it happens again please.
Re: zannusi zwd16270w
Hi.
They actually begin with E for Error, not C.
What fault code do you need to know about?
Re: Baumatic BDW13.
It looked like a Full Sized version of the Beko Slimline. Mind you, the installation was a joke. It took 2 hours of my life. FFS! 👿
Still, at least it did work.Re: Electrolux ERf 2832 Fridge Freezer problem
Hi.
This usually is an indication that the control board cannot sense the presence of the defrost heater. It could be a duff board, heater or wiring between the two. The fan will usually cease to run when the door is opened.
Any chance of having the product number?
Re: Electrolux EWD 1409
Hi.
It could be an insulation fault with the drier element. You will need an appropriate test meter.
Re: TB DH102 issues
If the product number is 911831027, then the part you will almost certainly need is the IWMS. Pt no: 1524624036.
Re: EWX14440W
You are looking for either Ed4 or E36 in the memory for the drier element issue. You may find if you check the insulation from cold all is well but it will break down once it has been running for a few minutes.
Re: Tricity Bendix TM 220 W
There is one heater assembly which consists of two seperate elements so it is possible that there is an open circuit. You could always test using a suitable meter.
Re: Tricity Bendix TM 220 W
Taken from user manual. May be things you would like to check.
Check that the air inlet and outlet vents are unobstructed.
The best way of evacuating the moisture is through a vent
hose to the outside of the building. Use the special 100
mm diameter flexible hose supplied with the appliance
connected to one of the air outlet vents with the collar
supplied.The unused outlets must be covered.
Never connect the air vent hose into an existing discharge
pipe or duct, as this could be dangerous, might disturb
neighbours and could cause the dryer to malfunction.IMPORTANT: This product is supplied with a 2.50 metre vent hose,
although the maximum length of the vent hose may be:
4 metres with NO bends, or 2 metres WITH 2 bends.Problems can be encountered in rooms fitted with a very
powerful central extractor fan. If you find that drying
times are too long, switch off the extractor or close its
grille whilst the tumble dryer is in use.A highly effective solution is to simply poke the vent hose
through a window or skylight. This might however cause
problems in winter because the dryer will draw in very
cold (and often also very damp) air through the open
window, so increasing drying times and leading to very
high energy consumption.If the dryer is fitted next to kitchen units, make sure
that the vent hose is not squashed. If the hose is
partially squashed, drying efficiency will be reduced,
resulting in longer drying times and higher energy
consumption.If the hose is completely squashed, the safety cut-outs
with which the machine is fitted may operate.Re: best toolboxes?
Thanks for the tip guys. I have just bought one from an Ebay seller for £35.74p delivered.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll? … 0421160566
Job done!
Re: AEG 40660
Hi Don.
I’m looking at TDS & what I’ve got shows that this model had a window that displays wash time as well as displaying a fault code.
Is that correct & if so, has there been no code displayed?
Re: Beko WMA 510W
Hi.
Most likely the control board has gone up the wall, although the motor can’t be ruled out.
Re: Tricity Bendix Fridge is freezing food
Hi.
From your point of view, the thermostat is much easier to replace so it may, depending on how you view the situation, be best to replace it & monitor. I suspect though hat the system may be more likely the cause & almost certainly the issue if this doesn’t resolve the issue.
A system fault could be quite pricey & may render the product beyond economical repair.
