[Turbo]

Re: Hoover GCC590NB-80 stopping.

Hi Kai
Went back to this dryer and had a thorough look for the front ntc with no luck ??

Thanks
Graham

[Turbo]

Re: Hoover GCC590NB-80 stopping.

Kaibart once again thanks for your help.
Would it be the exhaust ntc and is it a drum out job ??

Thanks

Graham

[Turbo]

Re: Hoover GCC590NB-80 stopping.

Hi Kaibart

Thanks for your comment.

I went back to this dryer on Friday and on the timed drying cycle it stopped after less than 5 mins so I took the damp towels out.
It took 5 mins to reset and then it ran fine with no damp towels, so I put the damp washing back in again and it ran ok.
So I’m baffled on this one.

Thanks

Graham

[Turbo]

Re: Bosch D/W Dispenser Problem

Another thing I should have mentioned is that my plug only has 2 wires and yet the new PCB has 3 connector points on the rinse aid PCB.
I have just watched a couple of youtube videos on fitting this part and both had three wires to that plug.

Graham

[Turbo]

Re: Bosch D/W Dispenser Problem

Thanks for the reply Dave.

The new dipenser has the rinse aid connector on the left side of the unit and not the bottom as is the case with the old one.
Not that the position matters, it`s just the plug doesn`t fit.

Thanks

Graham

[Turbo]

Re: comet…again!!!

Comet collapse on Radio 4 last night

http://www.bbc.co.uk/programmes/b04n338g

[Turbo]

Re: Siemens Dryer WT36V398GB/07 Filter/Hose Light

Thanks for your reply Paul.
Yes I did vaccum the whole machine including the heater which was quite blocked. Still giving the same fault though.
The dryer has been heavily used.

[Turbo]

Re: Liability Insurance Due

I have now!

Thanks as always Martin.

Graham

[Turbo]

Re: WT46W560 GB/01 Not Drying.

Does anyone know how you change the thermistor at the front of the dryer, do you have to take the front panel off or can you remove the right hand fan cover for access?

Thanks
Graham

[Turbo]

Re: WT46W560 GB/01 Not Drying.

Correct it has the heat pump Martin.
How does this model measure the damp in the clothes?

[Turbo]

Re: SMI69T15GB/01 Fault PO

Thanks yet again Martin for your help on this one.
The customer did ring me up first thing this morning to say the dishwasher had started to work again.
I did look at page 23 online and have told him to do the same assuming he has more problems with P00 etc

Graham

[Turbo]

Re: WI 12 S 140 GB/20 Door Lock Clicks

Cheers Martin the new door lock cured the fault.
It was a friends machine and they are moving this Friday so I was panicking a bit regarding the board!

Thanks

Graham

[Turbo]

Re: Washing Machine Leasing

A good idea really as the amount of waste our industry produces is shocking and it just keeps getting worse despite this site trying to encouage the opposite.
We don`t need the choices that we have. 5 or 6 good quality models would be enough. The job would not be as interesting but we would have a lot less hassle.
Most people who rent at the moment have no money so there is always going to be a problem with there.

Graham

[Turbo]

Re: Neff D/W 5943X2GB/31 Module Blown

Thanks for your help on this one guys, it turned out to be the dispenser as you suggested.

Thanks again.
Graham.

[Turbo]

Re: WFL 2066 GB/01 Suspension Leg Change

Thanks for your advice, I shall give it a go.

Graham

[Author]

Posts