Turbo

Forum Replies Created

Viewing 15 posts - 301 through 315 (of 428 total)
1 2 3 … 20 21 22 … 27 28 29
  • Author
    Posts
  • July 27, 2007 at 8:51 pm in reply to: circuit board repairs #222767
    Turbo
    Participant

    Re: circuit board repairs

    Could be worth a go but only 6 month Gtee compared to 12 months at EMW.
    Graham

    July 27, 2007 at 8:42 pm in reply to: Bosch WTL 5400 GB/04 Skipping Cycle #222760
    Turbo
    Participant

    Re: Bosch WTL 5400 GB/04 Skipping Cycle

    Sorry Greg WTL 5400 GB/04.
    Well I did give the condenser box a clean out but I will have a closer look at the fine mesh slots where the cool air flows.
    On the intial visit the pump chamber was full of grey sludge causing the water container light to come on prematurely but that is ok now.
    If the condenser box is ok have you any other suggestions.
    Thanks
    Graham

    July 21, 2007 at 4:10 pm in reply to: Hotpoint dishwasher BFI620 error message, what does it mean? #222159
    Turbo
    Participant

    Re: Hotpoint dishwasher BFI620 error message, what does it m

    I think you should test the heater first before making a purchase.
    In my case it was the heater but it could be board fault.

    POWER OFF BEFORE WORKING
    Remove base to gain access to heater.

    Graham

    July 21, 2007 at 4:02 pm in reply to: Almost had it with Hotpoint Ultima 865 #222176
    Turbo
    Participant

    Re: Almost had it with Hotpoint Ultima 865

    Not seen them on there recently but they could devote a whole series to them I reckon. 👿
    Graham

    July 21, 2007 at 3:46 pm in reply to: Almost had it with Hotpoint Ultima 865 #222174
    Turbo
    Participant

    Re: Almost had it with Hotpoint Ultima 865

    Only joking Martin 😆
    Graham

    July 21, 2007 at 3:45 pm in reply to: Almost had it with Hotpoint Ultima 865 #222173
    Turbo
    Participant

    Re: Almost had it with Hotpoint Ultima 865

    Sorry Martin had a bad week with this company and their awful products will try to behave in future 😥
    Graham

    July 21, 2007 at 3:13 pm in reply to: Almost had it with Hotpoint Ultima 865 #222168
    Turbo
    Participant

    Re: Almost had it with Hotpoint Ultima 865

    The only thing you are doing wrong is using it! this model is absolute cr@p, do your self a favour and get rid of it as it will always be trouble.
    Graham

    July 21, 2007 at 3:07 pm in reply to: Hotpoint dishwasher BFI620 error message, what does it mean? #222157
    Turbo
    Participant

    Re: Hotpoint dishwasher BFI620 error message, what does it m

    Light 2 and 4, that is a heat fault. did one yesterday fitted new heater all ok now.
    Graham

    July 12, 2007 at 7:26 pm in reply to: Hello? Hello? Hello? #220712
    Turbo
    Participant

    Re: Hello? Hello? Hello?

    A good case for banning the sealed outer drum I reckon 😉
    Graham

    July 5, 2007 at 6:58 pm in reply to: Free Training from Proctor & Gamble #219768
    Turbo
    Participant

    Re: Free Training from Proctor & Gamble

    May have a change of heart and give it a listen, he is calling back next week.
    Yes this Turn It to 30 campaign is sure to give us a lot more work, messy work but it pays the bills 😉
    Graham

    July 4, 2007 at 8:31 pm in reply to: Free Training from Proctor & Gamble #219760
    Turbo
    Participant

    Re: Free Training from Proctor & Gamble

    I agree Chris it was. Cant see the point on going on this so called follow up course really.
    Graham

    July 4, 2007 at 4:34 pm in reply to: Indesit WDE 12UK Start/Reset Switch. #219575
    Turbo
    Participant

    Re: Indesit WDE 12UK Start/Reset Switch.

    Thanks Jim will get one on order
    Graham

    July 3, 2007 at 7:51 pm in reply to: Hoover HNC 170 Heater Change? #219584
    Turbo
    Participant

    Re: Hoover HNC 170 Heater Change?

    Ok point taken thanks for the reply
    Graham

    July 3, 2007 at 6:52 pm in reply to: Hoover HNC 170 Heater Change? #219582
    Turbo
    Participant

    Re: Hoover HNC 170 Heater Change?

    Been to a few of these over the last couple of years and as yet I have ducked the job pushing it on to the manufacturer under the parts Gtee as I dont feel that happy about cutting into the wiring when the proper connectors have been supplied with the new heater. Due to the poor quality of these dryers I dont think I would attempt a drum out on this one 😥
    Thanks
    Graham

    July 2, 2007 at 6:55 pm in reply to: Hotpoint WD61P 185 deg Dryer Stat. #219064
    Turbo
    Participant

    Re: Hotpoint WD61P 185 deg Dryer Stat.

    Thanks for all your help on this one guys, new stat now in place after a bit of work with the pliers. Found 2 broken wires near the motor plug which I have fixed.
    Thanks again


    Graham

  • Author
    Posts
Viewing 15 posts - 301 through 315 (of 428 total)
1 2 3 … 20 21 22 … 27 28 29