[Turbo]

Re: Glaring design faults

The current Zanussi/Electrolux washing machines where the drain tube can be easily pulled off the pump housing, flooding the kitchen the next time it is used 😥

[Turbo]

Re: Hotpoint WD61P 185 deg Dryer Stat.

Thanks may have to go back and have another look.

[Turbo]

Re: Hotpoint WD61P 185 deg Dryer Stat.

Thanks Bryan blowing a gale down the old chimney 😆

[Turbo]

Re: Hotpoint WD61P 185 deg Dryer Stat.

Thanks Chris, just tried putting that number in to Connect system and it comes up 1605635 again but I am sure you are right having looked at a picture in the Parts Centre Cat, will ring the Rep and tell them to sort it out.

[Turbo]

Re: Connect

Local rep always happy to take parts back for me but do get fed up with the amount of pattern parts I receive having ordered genuine.
They must think we are stupid.
Are they selling pattern parts online to the unsuspecting general public I wonder?
Turbo

[Turbo]

Re: Sealed Tubs

Ken
Give it a couple of years and you will struggle to find a manufacturer who produces a machine that you can fit new drum bearings and shaft.
There are two groups making money here,(been posted before I know) the manufactures producing crap and the recyclers recycling the crap.
Work is certainly on the downward spiral for me and can only see it getting worse, a great shame because as you have said before yourself the best way to recycle is to repair.

Turbo

[Turbo]

Re: Indesit WIDL 102 Limited Prog Selection ?

All ok now got EMW to put eprom in new board.
Thanks Turbo

[Turbo]

Re: Washing Machine recommendations

The Bosch WAE 24162 is the machine to buy at that price, this comes with a 2 year parts and labour Gtee
The Hoover only comes with 1 years parts and labour Gtee so after the 1st year is up you will have to pay a high labour charge every time it goes wrong.
Turbo

[Turbo]

Re: Indesit WIDL 102 Limited Prog Selection ?

Thanks for the reply, does the new board have to be programmed ?
Turbo

[Turbo]

Re: TC470 Door Lock Cables

I am sure these cables are to long as I tried a second one on this dryer and it was no better. Customer still has machine but door is still not easy to open 😥
Turbo

[Turbo]

Re: siemens dishwasher top spray arm not turning

Would need the model number first

[Turbo]

Re: Bosch SGS56E02GB/35 Leaks

Door seal was ok and in position but will make sure arms are not getting jammed.
Thanks for that Greg

[Turbo]

Re: Zanussi FJ 1454W Board Fault ?

Thanks for letting me know about the E90 error code. The problem I have now is I cannot access the diagnostic system to configure the new board by holding down the skip/reset & start/pause button and turning machine on etc.
Thanks
Turbo

[Turbo]

Re: partscenter

Yes sorry to hear the girls at Partcenter are losing their jobs as I alway found them very helpful. This company goes from bad to worse it seems 😥
Turbo

[Turbo]

Re: AEG L12700VIT no display after testing pump terminals

Well if it was me I would go back to this machine armed with a new power module, door lock and wiring harness Prt no 1249331123 the lock and harness are always worth carrying I find.
Before fitting any of these parts I would check every single electrical component I could, check for earth leakage, correct resistance readings even check that new element you fitted.
If all ok I would fit the wiring harness to see if you can get a display on the interface.
If no better I would fit the door lock then the board which would have to be configured all the info on this is available on the Electrolux/Distriparts DVD.
Good Luck

[Author]

Posts