allan73

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 497 total)
1 2 3 … 11 12 13 … 32 33 34
  • Author
    Posts
  • August 8, 2011 at 2:16 pm in reply to: zwm616 #356633
    allan73
    Participant

    Re: zwm616

    Thanks for the reply 🙂

    Allan.

    July 7, 2011 at 7:45 pm in reply to: Qualtex 30mm hotpoint spider & bearing kit #355102
    allan73
    Participant

    Re: Qualtex 30mm hotpoint spider & bearing kit

    The question is though are the 30mm spider & bearings up to the job ? After all hotpoint must have made the spider obsolete for a reason 😕

    Allan.

    July 5, 2011 at 10:37 am in reply to: 31er14mht regulator replaced by 41er102c1p #354561
    allan73
    Participant

    Re: 31er14mht regulator replaced by 41er102c1p

    Please ignore my last post, just reread diamond h wireing reference properly 😳

    Allan.

    July 2, 2011 at 8:57 am in reply to: 31er14mht regulator replaced by 41er102c1p #354560
    allan73
    Participant

    Re: 31er14mht regulator replaced by 41er102c1p

    Am i correct in thinking the load output would be from no2 not sure about the neutral?

    Thanks again,
    Allan.

    July 1, 2011 at 8:07 pm in reply to: 31er14mht regulator replaced by 41er102c1p #354559
    allan73
    Participant

    Re: 31er14mht regulator replaced by 41er102c1p

    Cheers Steve, I didn’t get a link wire with it but I’m sure i can knock one up 8)

    Allan.

    June 29, 2011 at 6:33 am in reply to: TJ HUGHES #354366
    allan73
    Participant

    Re: TJ HUGHES

    I agree with Martin on this, TJ Hughes have in the past sold vacuum cleaners etc cheaper than I could buy trade.They obviously banked on large turnover of stock and when it falls away…… 😈

    Allan

    June 28, 2011 at 6:40 pm in reply to: {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} rate of a “scrapped” washer then ends up in landfill ? #354361
    allan73
    Participant

    Re: {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} rate of a "scrapped" washer then ends up in landfill ?

    Thanks for the reply Martin 😉
    I often wonder,when I take old M/c’s into the “metal recycling yard” how much of the metal, plastics etc gets reused and how much ends up in landfill.
    I suppose your correct and getting a definative answer is near impossible with various party’s putting their own spin on it. :rolls:

    June 24, 2011 at 10:52 am in reply to: LG12230FB Fill error #354093
    allan73
    Participant

    Re: LG12230FB Fill error

    Any Lg experts out there ?

    June 23, 2011 at 2:54 pm in reply to: Hoover A3632 Washer – old un #354108
    allan73
    Participant

    Re: Hoover A3632 Washer – old un

    If I remember correctly the hose is a vent for the steam when hot filling.
    As for the leak I would check the pressure chamber or pump for blockages.

    Allan.

    June 23, 2011 at 11:08 am in reply to: indesit WIA 101 uk #346258
    allan73
    Participant

    Re: indesit WIA 101 uk

    My guess would be main module 🙁

    Allan

    June 21, 2011 at 10:07 am in reply to: Beko wm5120s motor or mod? #353836
    allan73
    Participant

    Re: Beko wm5120s motor or mod?

    I think there are some threads on here about tacho magnets cracking on Beko’s.

    Allan.

    June 16, 2011 at 7:12 pm in reply to: Bosh srs431c12gb/23 drain pump removal #353701
    allan73
    Participant

    Re: Bosh srs431c12gb/23 drain pump removal

    Cheers Colin 🙂

    June 9, 2011 at 8:31 am in reply to: Bosh SG56302GB/12 F in display ? #353243
    allan73
    Participant

    Re: Bosh SG56302GB/12 F in display ?

    Thanks Martin,
    I’d better get the F’ing meter on it then 😆

    Allan.

    June 7, 2011 at 8:22 pm in reply to: Zanussi zwd1262w E23 & earth leak. #352961
    allan73
    Participant

    Re: Zanussi zwd1262w E23 & earth leak.

    Been back to this one and found a leak from the hose which runs from the condenser to the drum. The leak was running onto the pump, new hose on order.

    Allan.

    June 6, 2011 at 7:03 pm in reply to: White knight CL93 dead #352394
    allan73
    Participant

    Re: White knight CL93 dead

    Update,
    Module from Crosslee solved this,I think there was a duff relay on there. 8)

    Allan.

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 497 total)
1 2 3 … 11 12 13 … 32 33 34