Forum Replies Created
-
AuthorPosts
-
Allsorts
ParticipantRe: Zanussi tce7124w
Got it Martin… just what the doctor ordered..
Cheers
GeorgeSeptember 4, 2010 at 9:08 pm in reply to: Electrolux TDS Offline disk wont work in Windows 7? #329439Allsorts
ParticipantRe: Electrolux TDS Offline disk wont work in Windows 7?
Thanks Don 🙂
Allsorts
ParticipantRe: Zanussi tce7124w
Hi Martin and thanks for the good laugh… Much as it may seem strange, I didn’t even realise that the website had no email address.. however.. it is enquiries@secondhandheaven.co.uk
Hope you are keeping well
GeorgeAllsorts
ParticipantRe: Problem with PM’ing
tis ok.. think I figured it
Allsorts
ParticipantRe: bosch WFO2467 GB/17 fill and spin fault
Initial thoughts: Presuming that you have checked the motor brushes and they are fine, check to see if the motor comm is clogged with carbon .. and check the tacho
September 3, 2010 at 3:03 pm in reply to: Electrolux TDS Offline disk wont work in Windows 7? #329437Allsorts
ParticipantRe: Electrolux TDS Offline disk wont work in Windows 7?
What is there web address Don… and do I need to have an account with them?
GeorgeSeptember 3, 2010 at 2:38 pm in reply to: Electrolux TDS Offline disk wont work in Windows 7? #329435Allsorts
ParticipantRe: Electrolux TDS Offline disk wont work in Windows 7?
Does anyone know who still has this TDS version forsale as I can’t find a supplier with one in stock?
George
Allsorts
ParticipantRe: Indesit WidL102
Check that you have the correct supply on the correct inlet valve
Allsorts
ParticipantRe: Whitegoods Trade Association
The forms I got sent had a telephone number on (0845 1728001) .. I tried to phone it but the number is “Out of service” according to a message on the line.
Also… On the forms I was sent, the cost is £70, but the website still says £60.
Is it possible to pay by CC. DC. BACS. or Paypal?
Can someone supply a telephone number for reference please.
George
Allsorts
ParticipantRe: Indesit WIA111 acting wierd
Thanks for the confirmation guys …
I’ve gotta go out to it this afternoon, but TBH, being as it is still doing the full wash with no problems I think she will proberbly wait until it breaks and wont fullfill the job before getting it done.
cheers again
GeorgeAllsorts
ParticipantRe: Hotpoint WDL520
Check the cables from the pcb to the prssure swich for breaks/continiuity
George
Allsorts
ParticipantRe: Hotpoint WMA35 Confused
Check for bad soulder or dry joints in the areas that you repaired before.
George
Allsorts
ParticipantRe: WTA3204GB/09
Check the sensors are clean
George
Allsorts
ParticipantRe: Indeist Widl 126 Error code Heater TOC/Fan motor
Ive have a couple of these that, because of the lengthy wires to the thermistor, the wires have bared and have shorted on the screws inside the chassis or the wires have been broken as they catch on other parts inside the chassis of the machine.
Allsorts
ParticipantRe: Motor Tester
Thanks Phil… I’ll have a close look at that and see if I can’t use this in some way…
Just out of interest, how were you linking-up the motor to this?
George
-
AuthorPosts
