Forum Replies Created
-
AuthorPosts
-
bazza500
ParticipantRe: Proaction WQP12-9250 Dishwasher PCB
Part number is 674001020428 but no idea where has one
bazza500
ParticipantRe: Bearings and seal info needed
It is almost impossible to replace the bearings on this machine as separating the inner drum from the rear drum just doesn’t happen. Under warranty the complete drum assembly was replaced. Now Panasonic just replace the whole appliance.
bazza500
ParticipantRe: Door for Zanussi ZUD 9154 integrated fridge
I’m afraid the door is obsolete for that product.
bazza500
ParticipantRe: Door for Zanussi ZUD 9154 integrated fridge
Depends on the product number as to whether this part is available or not.
If you can get the product number I could let you know.
bazza500
ParticipantRe: zdf12002wa
Switch it on and leave it for 5 minutes and see if it works. It may be doing a full sensor check.
bazza500
ParticipantRe: Zanussi Washer Dryer (ZWD12270G1) has no power
The dryer element going to earth will cause these symptoms.
bazza500
ParticipantRe: Zanussi wm error code E6H
Possible earth leak on heater or heater relay fault
bazza500
ParticipantRe: John Lewis JLTDC09
Have you purchased the preprogrammed module?
April 5, 2015 at 10:57 pm in reply to: New replacement thermo overload cut-out switch not working? #426281bazza500
ParticipantRe: New replacement thermo overload cut-out switch not worki
That is correct. The cooling fan toc will show no reading on a multimeter until it gets above its operating temp. In this case 70oC.
The grill and cooling fan Toc’s will be different.
April 5, 2015 at 10:04 pm in reply to: New replacement thermo overload cut-out switch not working? #426279bazza500
ParticipantRe: New replacement thermo overload cut-out switch not worki
I’m not 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure here as I can’t get a diagram but I think there will be 2 toc’s on this appliance.
one is the grill overheat toc which should be a short cct and will open if the grill overheats and will stop the grill working.
The other will be the cooling fan toc which is normally open and will close at a certain temperature to bring on the cooling fan.
I suspect what you have done is replaced the cooling fan toc with the new grill overheat toc and this is why the fan is on continually.
Have a look for another toc on the appliance with the same numbers on it as the one you have bought.
April 5, 2015 at 1:52 pm in reply to: New replacement thermo overload cut-out switch not working? #426277bazza500
ParticipantRe: New replacement thermo overload cut-out switch not worki
Are you sure you’ve replaced the grill overheat toc and not the cooling fan toc?
Is it the oven fan running or the cooling fan?
bazza500
ParticipantRe: ikea dishwasher model RENGORA
Pressure switch modification required. part number 4055315073.
bazza500
ParticipantRe: Running a fridgecompresor w/o gas in
SAMURI wrote:You need to be F gas registered to work on systems now.
Bob
Not if it’s R600a.
bazza500
ParticipantRe: New Washing Machine – Recommendations?
George , you forget. Martin knows everything and knows it better then everyone. He’s great. In fact I’m surprised he doesn’t wear his underpants on top of his trousers.
bazza500
ParticipantRe: Whirlpool toploader 3RLSQ8033SWO
…..or replace the gearbox as a unit.
-
AuthorPosts
