Bernie

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 289 total)
1 2 3 … 7 8 9 … 18 19 20
  • Author
    Posts
  • March 10, 2011 at 3:24 pm in reply to: Hoover Dishwasher HFI3015-80 32900047 stuck on 3h delay led #346655
    Bernie
    Participant

    Re: Hoover Dishwasher HFI3015-80 32900047 stuck on 3h delay

    Not flashing just on, if I hold P1 down and switch on they go out but if you try to select anything they come back.
    Thanks for the reply Martin
    Bernie

    March 10, 2011 at 11:58 am in reply to: Hoover Dishwasher HFI3015-80 32900047 stuck on 3h delay led #346653
    Bernie
    Participant

    Re: Hoover Dishwasher HFI3015-80 32900047 stuck on 3h delay

    Thanks very much loopey for the info.
    I did manage to get rid of the 3h delay by holding down the delay button then switching on, it would then move to 6h if I did it again it moved to 9h and then to off.
    After trying to get into the self-diagnostic sequence so as to see the error code. I now have the led’s of P1 & P2 on and cannot get rid of them, I did get them off but when you switch off & back on again there back.
    I never did get into the diagnostic program, could not get past led’s P1 & P2 on, just on not flashing.
    Would I be right in assuming it’s the PCB, or could it be something else?
    Any suggestion
    Bernie

    March 9, 2011 at 7:29 pm in reply to: indesit is60v interlock wiring #346573
    Bernie
    Participant

    Re: indesit is60v interlock wiring

    From left to right. Red and white. Brown then Grey. For door interlock

    March 9, 2011 at 11:39 am in reply to: Hotpoint WT960 Dead #345906
    Bernie
    Participant

    Re: Hotpoint WT960 Dead

    Thanks Mike will give that a look too, have orderd new Harness that goes between the two boards.

    Bernie

    March 5, 2011 at 11:44 am in reply to: Hotpoint WT960 Dead #345904
    Bernie
    Participant

    Re: Hotpoint WT960 Dead

    Thanks for that Martin, it’s the only thing I can think of trying too.
    Bernie

    March 5, 2011 at 10:41 am in reply to: Hotpoint WT960 Dead #345902
    Bernie
    Participant

    Re: Hotpoint WT960 Dead

    Helo_75 Could you let me know if there was more in the memo as I am still having problems with this one?
    I fitted the returned board checked the pins in the plug to the fascia and main pcb tested them for continuity all ok, put it on a spin to test worked for 3/4 mins cancelled program was going to put it on a wash when the front facia display started to flash then went blank machine dead. Sent both facia and main modules to EMW for testing, Tony could not find anything wrong.
    Going back next week any help please.
    Bernie

    March 2, 2011 at 5:29 pm in reply to: Bosch Dishwasher SGV56A03GB/40 1 min remaining #345964
    Bernie
    Participant

    Re: Bosch Dishwasher SGV56A03GB/40 1 min remaining

    Thanks Martin it gives me some where to start to look
    Bernie

    March 2, 2011 at 2:46 pm in reply to: hotpoint wma44 #345994
    Bernie
    Participant

    Re: hotpoint wma44

    I think this has a variable spin and heat switch so can only guess the connectors have been switched.
    Bernie

    March 2, 2011 at 2:37 pm in reply to: Bosch Dishwasher SKT5102GB does not fill enough #345423
    Bernie
    Participant

    Re: Bosch Dishwasher SKT5102GB does not fill enough

    Thanks nomadPaul you were correct.
    This is a table top dishwasher, and there was a blockage in the pressure pot chamber and hose from sump to the chamber.
    Bernie

    March 2, 2011 at 2:32 pm in reply to: Bosch Dishwasher SGV56A03GB/40 1 min remaining #345962
    Bernie
    Participant

    Re: Bosch Dishwasher SGV56A03GB/40 1 min remaining

    I know I meggered the machine and all was ok but could this still be a faulty heater causing this?
    Any help would be much appreciated
    Bernie

    March 2, 2011 at 8:42 am in reply to: Hotpoint WT960 Dead #345901
    Bernie
    Participant

    Re: Hotpoint WT960 Dead

    Was that all the memo said or was there more helo_75
    Thanks Bernie

    March 1, 2011 at 11:08 pm in reply to: Hotpoint WT960 Dead #345900
    Bernie
    Participant

    Re: Hotpoint WT960 Dead

    Thanks for the quick reply

    Bernie

    March 1, 2011 at 6:07 pm in reply to: WMA Torx bolts #345912
    Bernie
    Participant

    Re: WMA Torx bolts

    I have got a colour gaz blow lamp (B&Q) heat up the spider around the Torx bolts then use torx socket, this works most of the time have used angle grinder on the ones it did not work on.
    Bernie

    March 1, 2011 at 12:58 pm in reply to: Bosch waa24171gb/12 Reset #345802
    Bernie
    Participant

    Re: Bosch waa24171gb/12 Reset

    I would like to agree with Rolf
    “Would be handy a list of all the reset procedures”
    Bernie

    March 1, 2011 at 12:15 pm in reply to: Bosch WAE28363GB/06 FD8802602326 F:21 #345542
    Bernie
    Participant

    Re: Bosch WAE28363GB/06 FD8802602326 F:21

    Have not been back as it’s in the country and don’t get out that way often.
    He say’s he will put cheque in post!
    I remember going to a Zanussi FL828 when the split cab first came out had to order new clutch motor took about 3 to 4 weeks by that time they had got a new machine had not told me until I phoned to book the call, never got paid.
    Still got the motor if anybody needs one as they are now obsolete according to Connections.
    Bernie

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 289 total)
1 2 3 … 7 8 9 … 18 19 20