[Bernie]

Re: LG WD12316RD Display goes blank

Thanks for the reply Mike
This one has three boards the facia one and two down the bottom rear left looking from the rear one is just a power supply the other is the main board both of these are sealed in with some sort of plastic and you can’t get to them to look for dry joint etc. I have been back and it did do it once for me power to main PCB so power supply PCB ok. Have advised it is the main board at £142.60 + VAT to me, RRP £190.18 they are going to get a new machine.
Again thanks for the reply
Bernie

[Bernie]

Re: Beko WMXD760W will not do anything

Fitted new lock all worked fine only door handle broken now!
Thanks once again Colin
Bernie

[Bernie]

Re: Beko WMXD760W will not do anything

Thanks for the reply Colin, I will give it a try
Bernie

[Bernie]

Re: Indesit WIDXL126 led’s2&3 flashing and door lock

Thanks for the replies
Bernie

[Bernie]

Hotpoint WF630

I dont know if this would help have a look here
viewtopic.php?f=3&t=12044

[Bernie]

Re: Hotpoint WT960 strange noise

Did have something similar cannot remember what make, the chasse next to the one of the suspension legs had a two inch crack.
Bernie

[Bernie]

Re: hotpoint aqualtis door seal/boot

I did one of these last week it is easy to do pulled machine out and tipped it back so as to give a little more room to work.
Also I found that the seal I got from connection had a large hole at the top as thought it was where a hose should go ( ie: jet wash) as the one on the machine did not have it. Got Connection to check part number and was advised that was the only part number C00254217 So I just found something to blank it of.
Bernie

[Bernie]

Re: Zanussi ZWF1432 stops between wash and rinses

Thanks for that Martin it’s worth a try
Bernie

[Bernie]

Re: Zanussi ZWF1432 stops between wash and rinses

Most of my test were empty although there was once when the washing was still in there. I did confirm that the customer had put a full load and was told yes.
I think you have got the answer there because she said that just as it was starting its spin after the rinse and before it stopped the machine made an unusual noise
Thanks for the reply gandh1
Bernie

[Bernie]

Re: Zanussi ZWF1432 stops between wash and rinses

I have only tested them from the test programme to check they work ok. It is very difficult to diagnose as it will not do it for me, even sitting and watching it go through a program. I am not sure EMW do this board. That is what I am suspecting it might be. As you say might be worth replacing the valves just in case.
Thanks for the reply Mike
Bernie

[Bernie]

Re: Hotpoint WMA66 Door light flashing

My thoughts to, thanks for the reply
Bernie

[Bernie]

Re: Hotpoint WMA66 Door light flashing

Tried cancelling child lock by holding the child lock button in for more than 5 sec
Also had door lock out to change it so tried it before I put it back. Did know about spring that is why I tried door lock out of machine.
Thanks for the quick reply

Bernie

[Bernie]

Re: VHD8142 flashing

I have had a few of these that have odd faults each time it was the Selector switch
Bernie

[Bernie]

Re: Indesit IWDC6125UK LED’s along the top flashing

Thanks for the reply idaom.
There were no vertical lights flashing. Just the option buttons along the top.
I was wondering if this machine has the same fault codes as the WIDL washer dryers which use the options buttons, i.e. F15 Drying Relay – check heater relay I assume the PCB is US.

Bernie

[Bernie]

Re: Hoover Dishwasher HFI3015-80 32900047 stuck on 3h delay

Thanks for the suggestion Martin, tried that but it did not work.

I also tried holding in P1 then switching it on, released the P1 button
then pressing the P1 4 times in 4 seconds, that did not work either.
Bernie

[Author]

Posts