bigsmokepiker

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 313 total)
  • Author
    Posts
  • in reply to: GW709 Fault Code 00001001 #235044
    bigsmokepiker
    Moderator

    Re: GW709 Fault Code 00001001

    709 Is 7 kg

    in reply to: GW709 Fault Code 00001001 #235042
    bigsmokepiker
    Moderator

    Re: GW709 Fault Code 00001001

    GW709 IS A Phase 5
    Fault code 9 Size error
    Reset Size
    Size setting mode press &hold water temp up then press power
    cold water led 5 Kg
    low water led 6 kg
    spin hold led 7 Kg Your case
    Press power to store in memory

    in reply to: margherita 2000 troubleshooting #128354
    bigsmokepiker
    Moderator

    Re: margherita 2000 troubleshooting

    What model Hoover is it
    Hoover branded front loads have been of the market for a number of years
    I would suggest a new one if the budget permits
    If Moneys Tight try LG WD8015C Should pay About $ 650.00
    2 year warranty Parts & repairs cheap down the Track
    If your after a better quality Washer
    Miele from $1600.00 AEG From $1300

    Penguin Spot on About Ariston Washer To many $$$ to Fix
    There track record here is well below average

    in reply to: Fisher&Paykel Intuitive Eco IW812 Error Code 49 #232537
    bigsmokepiker
    Moderator

    Re: Fisher&Paykel Intuitive Eco IW812 Error Code 49

    Fault code 49 Is A water suggests a Water valve Fault
    Cold valve fault Or can be Both Cold & hot
    Measure Resistance of Water valves (64 Ohm)
    Also check connections to water valve
    Also Check inlet hose filters for blockages
    In some instances the fault can relate to Motor controller
    Valves come as An Assembly Part # 421028P $54.00AUD
    Motor Controller 420787 $160.00 AUD

    Check your Warranty IW812 Is not That old They Have 2years

    in reply to: GW601-U F&P 11 year old washer #232409
    bigsmokepiker
    Moderator

    Re: GW601-U F&P 11 year old washer

    Service manual Suggest secondary fault cause Motor Controller
    IE Main PCB Part # 425260P About $200 Aud

    in reply to: GW601-U F&P 11 year old washer #232406
    bigsmokepiker
    Moderator

    Re: GW601-U F&P 11 year old washer

    Your all over the shop here a Bit
    But Lets look at diagnostic code
    11010000
    I presume Your reading R to L Code 208 (No Such Code
    Reading L to R Code (as you Should ) 00001011 (Fault code 11)
    This is a pressure sensor fault
    Check bowl is fully pumped out remove pressure tube blow thru tube to clear
    of water & reconnect (tube is connected to motor controller PCB)

    Secondary cause can be faulty Motor controller PCB
    Run sticky again for last fault code
    Dont worry to much about the two short beeps
    Power button off
    Press Wash Temp down & then power Let Go
    Press Advance button ONCE
    Read lights L TO R

    in reply to: Fisher & Paykel MW059 no power, can’t find fuse #231856
    bigsmokepiker
    Moderator

    Re: Fisher & Paykel MW059 no power, can’t find fuse

    Pump is Under Bowl Of Washer
    Tilt Washer back & it will stick out like the perverable ( On the Front RHS )
    Pump Should read 33 Ohm with multimeter

    in reply to: Fisher & Paykel MW059 no power, can’t find fuse #231854
    bigsmokepiker
    Moderator

    Re: Fisher & Paykel MW059 no power, can’t find fuse

    No fuse As Such
    Check pump (The Pump is part of the power supply) if pump is open circuit
    it will have to Be replaced (Resistance Should read 33 Ohm)
    Other Than that It will be the Main PCB (Motor Controller)
    If decide to replace Controller beware
    In some instances the Water inlet coils(Valves Should Read 64Ohms)can fail & Take out the PCB
    Its all bad news im afraid (Unless Its just the Pump)

    in reply to: F&P Smart Drive error 86 #231693
    bigsmokepiker
    Moderator

    Re: F&P Smart Drive error 86

    Actually fault Code 43
    Out of Balance Fault
    More than likely OOB Micro Switch fault (Terminals corrode )
    Numerous Threads on this issue

    in reply to: Fisher & Paykel E521T fridge #230669
    bigsmokepiker
    Moderator

    Re: Fisher & Paykel E521T fridge

    Thermal Fuse(2)Is part Of The Defrost heater (350w) Once open circuit they cannot be reset IE new element
    Heater located behind Freezer back panel
    Yes these panels are a bit tricky to remove & yes they can break easily.
    We have A little tool (Thin shafted Screwdriver with a hook at the end)which we fit into the vent holes of cover . You have to lever down & ease cover forward to release locking clips. Test Fuse s Etc with multi meter for circuit.
    You will probably see ice build up around evaporator ,heater would suggest you defrost before trying anything
    POWER OFF

    in reply to: Fisher & Paykel Intuitive Eco Error Code 52 #230143
    bigsmokepiker
    Moderator

    Re: Fisher & Paykel Intuitive Eco Error Code 52

    Diverter Valve Fault
    Remove Diverter Valve (Down near the Pump Under Bowl) Check for Blockages or broken hinge mechanism
    Check resistance of wax solenoid on diverter Valve
    Resistance Should be between 0.7 – 2.5kohm
    POWER OFF PLUG OUT

    in reply to: LG Washer Making Weird Fluttering Noise? #228207
    bigsmokepiker
    Moderator

    Re: LG Washer Making Weird Fluttering Noise?

    Thats my point
    Pumps from LG are Dirt Cheap
    If you are a Service Agent for LG a pump would be the First Thing i would Stock for use In & out of the warranty period
    It makes economical sense -Only one visit
    We also have to fit genuine items to Machines under Warranty

    in reply to: LG Washer Making Weird Fluttering Noise? #228205
    bigsmokepiker
    Moderator

    Re: LG Washer Making Wierd Fluttering Noise?

    The Pump that Goes in Your machine Fits About 30-40 Different
    Model LG Washer/Dishwashers going Back 7-8 Years
    Any Service agent Worth there Salt Would have one In Stock
    I Cant fathom how there would Not be one In NZ

    in reply to: Smart Drive 051 wont fill with water #229367
    bigsmokepiker
    Moderator

    Re: Smart Drive 051 wont fill with water

    43 out of Balance Switch fault

    in reply to: Smart Drive 051 wont fill with water #229365
    bigsmokepiker
    Moderator

    Re: Smart Drive 051 wont fill with water

    Simplest solution Would be A Faulty Out of Balance Micro switch
    Terminals Corrode & Washer thinks It is Out Of Balance
    It can Also be related to many other factors IE Main PCB or Rotor postion Sensor

    Run The Sticky & see if Can Post FAULT CODE

Viewing 15 posts - 166 through 180 (of 313 total)