Forum Replies Created
-
Posts
-
Re: F&P Smartdrive 051: fills, won’t agitate
Out balanc e Switch Error
Numerous threads about this fault in the Forum
Microswitch located under MAIN PCB(motorcontroller) RHS
Terminals Corrode
Machine thinks it is OOB when it Is NotRe: Help needed from an ex-pat appliance!!!!
OK S26 3 Versions
Model S26S5DF Version 858618153010
Model S26W3DF Version 858618153002
Model s26w3df Version 858618153000
Use same PCBS
Rear PCB Power
Part # 481221778171 supercedes to
Part# 481221778203 then to supercedes To
Part# 481221778215Front pcb
Part # 481221728001 supercedes to
Part# 4812227128003Re: F&P GW709, wont spin Error 10000011 & 10000010
RPS Sensor located under washerbehind wash motor
Sensor Suffers from corroded terminals
Check for Any signs of Leaking water asthis May be cause of Faulty RPS Sensor .
http–www.stokes-aus.com.au-StokesAP-Manufacturer_Info-FP-WASHERS_DRYERS-479153{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20Washer{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20Ph5{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20AW{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20LW{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20MW095{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20GW609{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20709{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20809.pdf
This Link May Help Page 18 Item 2 Is Offendng CulpruitRe: Constant alarm Fisher & Paykel E521T fridge
Check the defrost element /heater located in freezer behind back plate
Another to check would be fan Motor in freezer located in same area broken wiring to fan motor is a common problem .
If Your not sure what you are doing I would suggest a Pro
Ring F&P for a local service agent 1300650590Re: Australian LG dishwasher
OE IS A Drain error
Can be A blocked pump/or System blocked
PuMp Can Also overheat on these units & cut out
Pump is a Syncro type which you should be Able To source quite easily in UK
PCBS have also been known to be at Fault ( There was a recall on these in Aust)
Another thing i would check is the heating/element casing .
These have a tendency to leak & can also be a cause of the error
Some Info is on its WayRe: Help needed from an ex-pat appliance!!!!
Punching in The product code 858616815010 on my Whirlpool Service disk (Australia) comes up Blank
Same For The part numbers
The local S26 model you refer to Has Different part Numbers for The PCBsRe: Fisher & Paykel Fault Code????
Depends which Way your Reading Lights
If As posted Fault Code 208 There is no code listed
If We Read it As 00001011 Fault code 11 Pressure Sensor fault
Check Pressure Tube has not Dislodged or Clogged Blowing thru tube can Clear any blockages
Secondary Fault could be to due to faulty Display Module (Top PCB)
Pressure Sensor is Integrated Into The Display Module.
Note When checking/removing pressure tube ensure there is no water in The bowlRe: Fault code 32 on F&P GW501-F
According to fault Codes 32 Pump circuit error
The display module has detected that pump is on when it is off
Action Check for Moisture in Console Area or Faulty Display Module
Fairly Unusual error this Id still Check Pump OOB SwitchRe: Fisher Paykel GW703-U washer problem
More than likely Lid Switch fault ( magnetic reed switch)
Switch located under Hob RHS
Part # 426457 About $40.00 AudRe: GW708K WILL NOT FILL
More than likely Lid Switch fault ( magnetic reed switch)
Switch located under Hob RHS
Part # 426457 About $40.00 AudRe: f & p iw 810 fault code 105
What stage of the cycle was the machine at
IE Was it Filling,washing,pumping out water Spinning?
Simplest thing to check would be drain pumpRe: Fisher&Paykel LW085 error code 8
Typical things to look for Out balance microswitch corroded terminals Etc
Rotor sensor /Numerous threads on this Problem
Washer Must pump All the Water before it goes on to Spin
Check pump for blockages Or Over heatingRe: LD-12AW2 Overfilling
Possible Causes
Pressure Switch Located At front Bottom Panel
Water inlet Valve (Located At Back Where Inlet Hose Screws Onto)May Not be Closing Properly Due faulty Valve or FAulty PCB
PCB is different to LD14AW2There was a recall on this Model For Faulty PCBs
Ring LG service 1800643156
