Forum Replies Created
-
Posts
-
Re: MWO59NZ error 00101011 when it stops….
This Link Will Show Where Part is
If Any doubt maybe get someone capable
http://www.stokesap.com.au/Manufacturer … {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}20809.pdfPAGE 8 No 19
Re: fisher paykel gw608 where is the fuse?
Fuse is in the motor controller (main PCB)
Check with meter
Note If fuse this usaually blows for a reason But for the price of a new fuse its worth a try
Also bw aware the pump forms part of the power circuit in this model
The pump or Wire to pump may be the culpritRe: MWO59NZ error 00101011 when it stops….
OOB Balance switch (microswitch) located under Motor controller in the top console area Terminals corrode & or braket that holds switch can break
Re: F & P GW603 Noise coming out of bottom!
Fault code 40
When doing a bowl check the module has indicated that the bowl has not engagaed correctly
Areas to check are The Clutch & or pressure switch tube
CHeck to see if Bowl is lifting up & down corretcly when bowl is empty
Check pressure tube in the Control panel Area (Clear tube That fits onto motor conrtoller) remove Tube stick your ruby lips around it & give it A good blow Refit & check washer operation
Noise can be from these problems
But when you replaced RPS DID You notice any signs of leaking water
Bearing noise would be fairly obviousFinally fault 40 can relate to pressure switch which is integrated into motor controller
Re: Save this wounded family handyman from losing his confid
You said it was a green PCB GW708 pcb is Generally Yellow
Green PCb Is For a GW 703
Size Setting For This is differwnt
Press & hold StartPaiuse Button then power
Press power Again to Store in memoryWhat color was original PCB ?And there should be part # on Old PCB
Part # for GW708 Shouls Be 426204 (yellow)
Re: Fisher Paykel IW811 “not getting hot water” an
Testing The Hot water valve
Press &hold Lifestyle button then power button It will give 2 short beeps
release buttons
Press how dirty up button to test hot valve down button to test coldRe: Fisher & Paykel GW703 Very Slow Water fill
generally cold water valve Fault Part # 426143 about $45 AUD
Simple to change Numerous threades in his forum.Re: Fisher Paykel IW811 “not getting hot water” an
Divertor valve (Sits near pump ) can be a pest We tend to replace divertor valve when doing a motor controller It tends to cause less heartache down the track
Re: Fisher Paykel IW811 “not getting hot water” an
Hot & Cold Valve are 24V DC Coils 64 ohm
If not Getting 24 V to Coils Usually suspect Motor controllerRe: Fisher Paykel IW811 “not getting hot water” an
Fault code 136 IS Motor Stall Fault
The Motor Controller has been unable to start the motor. Possible causes of this fault are
Faulty motor harness, faulty or jammed motor, seized bearings or seals,
Motor Controller (PCB), Rotor Position Sensor or harness
Check if bowl & agiatator Move Freely
From Past experience it can be generally the RPS Sensor or Motor controllerRe: Fisher & Paykel Dishwasher DW920 Fault Code 29
29 IS NOT A FAULT CODE
Fault codes are normally F1 /F2 ETC
The 29 is probably the time remaining
Could be numerous causes for machine stopping
Most common fault can be to do with the door latch /door siwtch Latches have a tendency to break
Further investigation is neededRe: Fisher and Paykel MW511 replace & program motor cont
Programming is for Size Setting
There should be instuctions with new Controller
But if not
Press & hold Temp up Button then press power button
Press wash temp up button until cold LED is on
Press power to lock in & exit modeRe: possiable re-gas needed
Are the fan Motors operating
Ie Fan motor at Evaporator & Condenser fan motorRe: miele km5757
Live (phase) L 2 not available -Check mains connection
Neutral N conductor for right power module not available (bridge fault between terminals 4–5)
Check that bridge is present between terminals 4–5
Check that bridge between terminals 4–5 has good contact
Fit bridge between terminals 4–5 if necessary
Check connection cable (including plugs) between filter/control module (2N1) and power module, and exchange it if necessary
Or Electronic unit faultRe: F&P Smartdrive 708 elec. burning smell
Id Still check drain pump
Pumps Have A thermal overload in them (ie Pump Shuts Down if gets to hot)
By letting it Stand for A while pump cools /and will pump til it overheats again.
Machine wont spin until it pump s water out
Does the Machine Let In water & Wash ????
