bryan-206

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 104 total)
  • Author
    Posts
  • in reply to: washing machine no power #382881
    bryan-206
    Participant

    Re: washing machine no power

    Unplug the wiring block from the mains filter. Common for these to burn out.

    in reply to: washing machine no power #382880
    bryan-206
    Participant

    Re: washing machine no power

    Do you have power going into the machine?

    in reply to: Daewoo American style fridge freezer #383123
    bryan-206
    Participant

    Re: Daewoo American style fridge freezer

    As above fan will be switched with door. May also be temperature controlled. Some don’t start till evap is frozen. Of course the evap sensor would have to give the correct readings also.

    in reply to: indesit di450 fault #383167
    bryan-206
    Participant

    Re: indesit di450 fault

    Are you certain you replaced the correct relay? Also what led you to replace the relay?

    in reply to: indesit di450 fault #383166
    bryan-206
    Participant

    Re: indesit di450 fault

    The PCb……?

    in reply to: AEG OKO Lavamat 610 Motor not turning #383235
    bryan-206
    Participant

    Re: AEG OKO Lavamat 610 Motor not turning

    Depends on the damage. You will have to remove and inspect. Bryan.

    in reply to: Zanussi TCE 7276 W no heat #383217
    bryan-206
    Participant

    Re: Zanussi TCE 7276 W no heat

    Agreed with above. Most sensor dry driers will check dampness before heating. Heater relay on PCb is common failure for zanussi

    in reply to: Samsung RS21 Refrigerator Over Icing #383212
    bryan-206
    Participant

    Re: Samsung RS21 Refrigerator Over Icing

    I’d say you have possibly attached the thermal fuse to the heater rather than behind the evaporator. Heater will get hot enough to trip th/fuse if in direct contact….. PCb failure is very very rare. Did the heater work once all was replaced?

    in reply to: AEG OKO Lavamat 610 Motor not turning #383233
    bryan-206
    Participant

    Re: AEG OKO Lavamat 610 Motor not turning

    Motor has probably taken out tracks on PCb.

    in reply to: Samsung RSG5DURS Diverter solenoid #379922
    bryan-206
    Participant

    Re: Samsung RSG5DURS Diverter solenoid

    Top left and middle right button for 8 secs. Beep beep and blank display. Middle right will cycle through functions. Cooling and defrost. Forced operation must be used when gassing I believe as only freezer circuit is open on initial power up. Unless forced otherwise

    in reply to: Washing A PC In A Washing Machine! #382858
    bryan-206
    Participant

    Re: Washing A PC In A Washing Machine!

    What a waste of life minutes.

    in reply to: SMEG FAB30RS7 #382468
    bryan-206
    Participant

    Re: SMEG FAB30RS7

    Scrap. With the pressures involved and the use of flammable gases this kind of repair should never be carried out….

    in reply to: Samsung RS21DCNS main pcb clicking/chattering #377609
    bryan-206
    Participant

    Re: Samsung RS21DCNS main pcb clicking/chattering

    Does your machine have ice maker?

    in reply to: What do they mean? #382477
    bryan-206
    Participant

    Re: What do they mean?

    Lol. Very light reading….

    in reply to: Bosch FL, dispenser and fascia melted, I’m baffled! #382310
    bryan-206
    Participant

    Re: Bosch FL, dispenser and fascia melted, I’m baffled!

    Possible that she has put in some kind of chemical that has reacted with the detergent…..

Viewing 15 posts - 61 through 75 (of 104 total)