Forum Replies Created
-
Posts
-
Re: Diplomat ADP8112 – Door not closing & can’t set prog
ailmcsnail wrote:
Hi Clivejameson – thanks for the advice, however what do you mean by the fascia – it is an integrated unit and all the controls are on the top inside the door which can only be accessed when the door is open – is it the whole panel at the top where all the buttons etc are? How easy is it to replace this and does that include the catch?
Many thanks
Louise
Yes that’s the fella…black plastic runs the width of the door at the top behind your cabinet door…and no, the catch is a separate part 😉
The good news is these parts aren’t as expensive as you might imagine…email to Shop@ with model and serial should get you the details if you find you need them. (do investigate first)
As far as fitting them goes we cannot give specific advice, but you will need the correct size Torx screwdriver and a little patience…not a difficult job but be careful of some very sharp door edges.
Plug out at all times if having a go yourself. :zap:
HTH?
nomadPaul wrote:Can i ask what the theory is behind the running of elements with the earth disconnected for a few minutes ? Is it to clear the element of moisture in some way ?
:tup:
Re: Bosch SGS43A12GB/27 dishwasher
I just wonder if the water board have been doing work, they may have ‘posted’ some muck along the pipe in which case check the inlet filter 😉
Re: More pictures guys please!
Here’s some of a grill element just at the point that it lets go…notice how mis-shapen it is, and the fact that it was working despite the (several) splits in it’s casing.
Re: Smeg D I 612 C dishwasher
If the diaphragm in the antiflood doesn’t lift during the fill (E2 error) then have a peek at the dispenser solenoid…flexing the terminals during a continuity test usually shows the fault 😉
Re: Carbon Brushes
kwatt wrote:
The one’s that aren’t used should be just fine. 😉
K.Nope sorry Ken, can’t aqree with that one 😆
Re: Servis washer M3024 Spin Cycle, wont speed up
jimyorks wrote:
Could the drum belt coming off have caused this because what i can find out from my other half it happened just after this?More likely the other way around…poor speed control throwing the belt off 😉
Re: Servis washer M3024 Spin Cycle, wont speed up
The control module for the motor is faulty 😕
Have a look here to identify it, or contact Shop@ with the model, serial and spin speed 😉
Re: Carbon Brushes
iadom wrote:On my patch I have many hundreds of Hotpoint & Hoover machines well over 20 years old still going strong.
Jim.
And how many Hotpoint and Hoovers bought today will be around in another 20 years time?
Answers on the back of a stamp please 😆Re: Help!! I need a new cooker
wsts wrote:
and even comes with a “thermostatically controlled oven” 😆No expense spared there then? 😆
Re: Diplomat ADP8112 – Door not closing & can’t set prog
This one is made by Smeg so….
A quick search on here for ‘Smeg AND reset’ will tell you how to reset…as long as the pcb hasn’t let go. 😕
The door will probably need a new facia, and possibly the door catch too if it’s worn (the facias break allowing the catch to drop inside)
The parts are surprisingly cheap for Smeg…the facia is around 20 quid IIRC
Re: Neff S5457X0GB/02
gegsy wrote: You a betting man Clive 😆
Greg
Wish i was…i tipped South Africa for the rugby 😕
😆
Re: Neff S5457X0GB/02
Greg, isn’t that ‘1 minute left’ actually error code 1 which is no heating?
…in which case the most likely culprit is the heater itself 😉
Andrew, the only satisfactory way to confirm is to meter the heater, and if it’s faulty will need replacing…not cheap (circa £80 ) and it’s a big strip-down job to replace 😕
If you need professional help then try the link below, or if having a go yourself then unplug before doing anything :zap:
