DentedPorsche

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 915 total)
1 2 3 … 14 15 16 … 59 60 61
  • Author
    Posts
  • June 14, 2008 at 6:00 pm in reply to: Starts but does not fill…now #254467
    DentedPorsche
    Participant

    Re: Starts but does not fill…now

    Really need the serial number but without it I’d say that this model gives a continuous flash for any error. It needs the engineer to access the electronics to obtain the correct error code.

    June 12, 2008 at 8:57 pm in reply to: WHIRLPOOL S20DRSB33 PCB BOARD ONE OR TWO #254557
    DentedPorsche
    Participant

    Re: WHIRLPOOL S20DRSB33 PCB BOARD ONE OR TWO

    Hiya,
    It would really depend on the problem.
    It’s a 2004 machine so could have 1 board replaced and the other should work ok with it.


    Brian

    June 12, 2008 at 6:07 pm in reply to: Bosch tumble dryer #254488
    DentedPorsche
    Participant

    Re: Bosch tumble dryer

    ROFLMAO
    😆 😆 😆

    June 10, 2008 at 10:16 am in reply to: Zanussi ZCE7700X cooker – Help needed with Clock wiring diag #253738
    DentedPorsche
    Participant

    Re: Zanussi ZCE7700X cooker – Help needed with Clock wiring

    Thanks Chris, Sadly, that’s the same info I found and sent. I’ve still not found anything regarding changing / rewiring to a different clock.

    😥
    Brian

    June 9, 2008 at 7:58 pm in reply to: Zanussi ZCE7700X cooker – Help needed with Clock wiring diag #253736
    DentedPorsche
    Participant

    Re: Zanussi ZCE7700X cooker – Help needed with Clock wiring

    😳 Mike,
    sorry, I forgot about chasing this one up.
    Hopefully Penguin got the stuff you need, although I’m mystified, I can’t find anything about this change anywhere.

    Brian

    June 9, 2008 at 7:56 pm in reply to: Beko f/f #254197
    DentedPorsche
    Participant

    Re: Beko f/f

    Hiya,
    Mail on it’s way to you now.

    Brian

    June 9, 2008 at 4:31 pm in reply to: Whirlpool 853703610600 #254165
    DentedPorsche
    Participant

    Re: Whirlpool 853703610600

    Thanks John, I’ll check that out and let you know how it goes.

    Brian

    June 9, 2008 at 4:27 pm in reply to: Beko f/f #254196
    DentedPorsche
    Participant

    Re: Beko f/f

    Hiya,

    E 0 is a freezer sensor failure.
    I’ve got self test document somewhere, if you want it. Need your email address though.


    Brian

    June 9, 2008 at 3:58 pm in reply to: Whirlpool 853703610600 #254163
    DentedPorsche
    Participant

    Re: Whirlpool 853703610600

    Hi Phil, I wish mate. Regards to Leigh when you see him.

    John, thanks for that. The numbering on the switch is different but I’m pretty sure I’ve got it ok.

    Now I’m stuck with a fault I’ve not come across before.
    Machine goes through the wash ok, empties, refills for the rinse and………. just stops. The timer and now the pressure switch have been replaced but same fault as before replacement.

    Any ideas?

    Thanks
    Brian

    June 4, 2008 at 8:34 pm in reply to: wpool ff fault code cf #253819
    DentedPorsche
    Participant

    Re: wpool ff fault code cf

    Hiya,
    CF is communication failure. Normally front pcb at fault.
    You need to check the date code to see if it needs just the front or both boards.

    Brian

    June 4, 2008 at 1:59 pm in reply to: Zanussi ZCE7700X cooker – Help needed with Clock wiring diag #253733
    DentedPorsche
    Participant

    Re: Zanussi ZCE7700X cooker – Help needed with Clock wiring

    Hiya,
    Sent you a pdf, may not be the answer you’re looking for though. It’s to do with the top oven timer facility?? 😕

    Brian

    June 4, 2008 at 6:50 am in reply to: Zanussi ZCE7700X cooker – Help needed with Clock wiring diag #253731
    DentedPorsche
    Participant

    Re: Zanussi ZCE7700X cooker – Help needed with Clock wiring

    Hiya
    Need an email address to send the info to.

    Brian

    June 3, 2008 at 9:40 am in reply to: Fagor Dishwasher LFU013SX #253588
    DentedPorsche
    Participant

    Re: Fagor Dishwasher LFU013SX

    DentedPorsche wrote: Usual suppliers don’t recognise the model number but it’s definitely correct.

    Thanks
    Brian


    😳 😳 😳 😳 😳
    Model number is correct now. 😛

    May 31, 2008 at 1:59 pm in reply to: baumatic bfd60ss #253349
    DentedPorsche
    Participant

    Re: baumatic bfd60ss

    Hiya,
    Send me your email address and I’ll send the file by return. It’s a pdf.

    Brian

    May 31, 2008 at 1:04 pm in reply to: baumatic bfd60ss #253347
    DentedPorsche
    Participant

    Re: baumatic bfd60ss

    Hiya,
    1st, sorry, don’t know.
    2nd, Got the service manual if it’s any good to you.
    3rd, Good old Chinese build quality. Haier machine I’m afraid.
    🙁

    Brian

  • Author
    Posts
Viewing 15 posts - 211 through 225 (of 915 total)
1 2 3 … 14 15 16 … 59 60 61