DentedPorsche

Forum Replies Created

Viewing 15 posts - 271 through 285 (of 915 total)
  • Author
    Posts
  • in reply to: De Dietrich FW4448E12 #247974
    DentedPorsche
    Participant

    Re: De Dietrich FW4448E12

    Hiya,
    No problem Ken, not seeing it again till the end of the week.
    😀

    Brian

    in reply to: De Dietrich FW4448E12 #247972
    DentedPorsche
    Participant

    Re: De Dietrich FW4448E12

    Thanks Dave, Any info is most appreciated.

    Brian

    in reply to: De Dietrich FW4448E12 #247970
    DentedPorsche
    Participant

    Re: De Dietrich FW4448E12

    Thanks for that Ken.
    Any way you can send the info? Is it pdf or something else?
    Any info is better than what I’ve got. LOL.

    Thanks
    Brian

    in reply to: Whirlpool APD W/1 Dishwasher #247096
    DentedPorsche
    Participant

    Re: Whirlpool APD W/1 Dishwasher

    Model number isn’t correct. What’s the 85 number on it?
    Start light should be flashing an error code to you. Count the flashes between pauses, the codes are in the “known error codes” sticky.

    Brian

    in reply to: Whirlpool AKZ151/1X wont move off stop #246963
    DentedPorsche
    Participant

    Re: Whirlpool AKZ151/1X wont move off stop

    monkey wrote:Hi Guys
    I have replaced the switch but you set the time.It wont change from the stop display.Any idea which board could be faulty.

    Give us the full story then. Why did you replace the switch? What was the original fault.
    Switch it off at source. Put the controls (oven selector) to off. Power it on again. Press the switch button 3 times, you should be able to set the time, if it came off stop.

    Brian

    in reply to: error ‘FO3’ whirlpool electric oven AKZ161 / 03IX #246921
    DentedPorsche
    Participant

    Re: error ‘FO3’ whirlpool electric oven AKZ161 / 03IX

    Capricorn is the main pcb.

    Brian

    in reply to: Diplomat ADP8322 Rinse light on #246811
    DentedPorsche
    Participant

    Re: Diplomat ADP8322 Rinse light on

    You need to count the flashes from the light. Error codes are in the “known error codes” post.

    Brian

    in reply to: energy reg wiring?? #246478
    DentedPorsche
    Participant

    Re: energy reg wiring??

    Go to the stickies “Diamond H” and download the file there. You’ll find a lot of info 😉
    Brian

    in reply to: Smeg Oven #245870
    DentedPorsche
    Participant

    Re: Smeg Oven

    Thanks for that Chris. It’ll help loads when I go back.
    Just got to find out now what on earth they’ve been sending me. 😕

    Thanks
    Brian

    in reply to: Smeg Oven #245868
    DentedPorsche
    Participant

    Re: Smeg Oven

    LOL.
    Sorry Martin,
    It’s SE20XMFR.1
    Serial is 40166690

    Thanks
    Brian

    in reply to: whirlpool stops mid wash #245379
    DentedPorsche
    Participant

    Re: whirlpool stops mid wash

    Obvious question, did it empty the water?

    Brian

    in reply to: whirlpool stops mid wash #245377
    DentedPorsche
    Participant

    Re: whirlpool stops mid wash

    Hi Alan,
    The 85 number would give the exact model.
    However, on the one I checked the spin speed leds should be flashing to indicate the fault.

    Brian

    in reply to: Baumatic DW24E1 Cod 906471071 #245208
    DentedPorsche
    Participant

    Re: Baumatic DW24E1 Cod 906471071

    Thanks Dave. PM on it’s way.

    Brian

    in reply to: WHIRLPOOL AWO/D 4705…8592 33315000 #245056
    DentedPorsche
    Participant

    Re: WHIRLPOOL AWO/D 4705…8592 33315000

    Check the carbons first. Motor should turn as part of start up checks.

    Brian

    in reply to: Baumatic BDW15 Dishwasher #244207
    DentedPorsche
    Participant

    Re: Baumatic BDW15 Dishwasher

    Thanks Jonah. Pm sent.

    Brian

Viewing 15 posts - 271 through 285 (of 915 total)