[eastlmark]

Re: Neff dishwasher door won’t lock

check the u shaped hinge bearings have not dropped out.

[eastlmark]

Re: neff microwave E300 error

Just to close this thread, it turned out to be the control module in the centre of the front panel that needed changing.

[eastlmark]

Re: Weird part descriptions

Whilst searching for a Bosch pump, BSH620774 on Qualtex I came across this: the mind boggles what it is.

BOSM665 Modular 2 seater sofa cover
Dealer Price: £28.00stock

[eastlmark]

Re: whirlpool taking over indesit

Just had my first Indesit co invoice with the Whirlpool logo on it….. ironically for a partfinder disc. Now I wonder what will happen to that in the future?

[eastlmark]

Re: WF540P serial no 471614445

screwed tub is C00112573

Welded tub C00143606

[eastlmark]

Re: Smeg oven, no fan element?

not at unusual, although always a surprise when you remove the panel and there isn’t one there. Whirlpool and Indesit also have/had fan ovens in there range like this.

[eastlmark]

Re: Smeg WDI16BA1 washer dryer (dryer problem)

have you had the fan out to check for build up on the blades? Also check the water valve is ok and being energised (might not start for quite a while), also check the ntc in the front duct is not covered in fluff (its easy to pull this out). Have also had “sticking” fan motors that don’t start up without a bump start every once in a while- unless it does it while you are there its hard to prove. Obviously ask the customer about overloading and not turning off before the prog finished.

[eastlmark]

Re: De Dietrich oven trips electrics when turned off.

Check the fan motor, take an insulation reading cold and then run it for a few minutes and do the same. see if it has come down. Had similar issues on Electrolux ovens.

[eastlmark]

Re: Panasonic NA147VB2 washing machine

yes front comes off, cannot remember how but its quite easy IIRC

[eastlmark]

Re: Smeg M/oven upper element Part numberif possible, Thanks

TELL wrote:Hi eastlmark,
Terry here again, am l missing something here I see that smeg list the A42 from 2003, with a dual element, so what about the element before 2003 for the A42’s. Any information on the part number for these, or is there an equivalent single element.
TELL. .

Yes even before 2003 they were twin elements. Funny enough attended one today! you guessed it a twin element.

[eastlmark]

Re: Smeg M/oven upper element Part numberif possible, Thanks

You need to read this:

eastlmark wrote:All A 42’s are shown as a twin type element there. from 2003 it was 806890527

[eastlmark]

Re: Connect Prices

OT I know as its qualtex but if only we could get away charging the RRP for this:

BEKBE462900010
view alternates

stock
BEKO ELEMENT FAN OVEN 1800w
RRP £68.23
Dealer Price £7.69

[eastlmark]

Re: Smeg M/oven upper element Part numberif possible, Thanks

All A 42’s are shown as a twin type element there. from 2003 it was 806890527

[eastlmark]

Re: Electrolux Washer Dryer Prod No. 91460600(01)

eastlmark wrote:

Mine is booked in for today, (Thursday) will let you know outcome.

Well, after an eyes shut moment when switching on…. it worked!
Did have a very close inspection of the old board before powering up just to make sure mind.
Chances of getting Electrolux to own up to a faulty pcb are slim I would guess. Funny thing is the new pcb is sealed in a packet with a label stating “sensible components inside- no return once opened” Best of luck with it.

[eastlmark]

Re: Electrolux Washer Dryer Prod No. 91460600(01)

jason1970 wrote:Morning Gents

Thank you for the replies, sorry I was unable to log on over the weekend.

Eastlmark. Thanks, that is the correct product number. I’ve had two previous AEG branded integrated washer dryer with same fault, both were repaired with new modules so I hope yours goes the same!

Bazza500 and Bluephill. Dryer elements definitely ok and I have unplugged them and tried machine and get identical error. Not sure how to put this machine into diagnostic mode? But not sure even if I could it would help as the LCD display just has random sections lit. Also as I rotate the programme selector switch I either get no indication on, just the start button lit red or the random LCD display. Very strange and certainly looks like a faulty module. This machine does have a second much smaller dryer module, could this have any affect on the new module? Not ever had one of those fail before but I don’t do that many Electrolux machines!

I guess I’ll have to order a second new module and keep my fingers very firmly crossed unless anyone has any other idea??

Thanks again for your help

Jason

Mine is booked in for today, (Thursday) will let you know outcome.

[Author]

Posts