Forum Replies Created
-
Posts
-
Re: Technics door seal
479459 Jimbo,
think you will find that the “1” after the “TT” is in fact an “i”Re: Smeg DWI612C
dave-m wrote:Managed eventually to reset it and put it on a wash, not 1 minute in it does that dreaded pulsing action.
Time for the bin me thinks,Cheers for the help
d
you did try a coil on the dispenser first I hope?
Re: Oops, wrong label stuck on… sorry
kwatt wrote:It’s an external site so I can’t fix it… But if some independent people tel them it’s broken…
K.
how can it be an external site? its an extension of the ISE web site so can you not just create a page for the url they have shown? is it the php bit thats the problem?
Re: Miele W918
if this is the type that the side panels come off, then also clear out the “Y” piece in the dispenser hose and the 2 thin pipes that come from it, often a cause of poor spins.
Re: DIPLOMAT ADP8902 fault help
sounds like its still on program. Door switch ok? hold down prog button and it may re set. if not, disconnect circulation pump and see if it clears, could be earth fault on the pump. Smeg one this.
Re: howden HJA8640 dishwasher
you pressing the start button? or canceled the existing program? These things start up at point of failure even after being unplugged for weeks.
should bring the drain pump on first.Re: eSpares Bought By Connect?
possibly its not till you look at their latest creation: http://www.buyspares.co.uk
to understand their scope fully.
GP checking prices over several seemingly different sites are in fact just dealing with a different store front. Assuming E spares will keep its own identity as well.Re: Whats the most annoying thing customers do?
funkyboogy wrote:thats a bit creepy mate –
ally
not creepy, just being responsible, after all I have asked whoever to call and know how it feels to be on the receiving end of a no show at the door. Whats more, I dont want to miss out on my repair/delivery/whatever!Re: Aeg oven B4140-1-M
think you need 899661914356/4 but looks like its oboslete. Cannot find the exact model number you have quoted but for most of the other B4140-m it is the one above. product code could confirm…..
Re: Smegging Dishwasheer
handle is 764730231
for the other bit there is a mod
order both:
769350131
764730267model number is correct btw.
Re: Whats the most annoying thing customers do?
Goatboy wrote:Just getting people to answer the bloody door seems like hard work atm 😕
Nearly every job…
Ring Ring
“Hello?”
“Hi! Is that Mrs blah blah blah?”
“Yes.”
“It’s Paul. Here about your dishwasher? I’m stood outside banging on your front door! I rung you ten minutes ago, to say I’d be with you in ten minutes!”
“Oh, I thought I heard something.”:rolls:
Whinge over!
its also amazing how many folks are vacuuming the house when we call and can therefore not hear the bell, knocker,telephone.
When I am expecting anyone to visit myself, I am by the window, checking every car i hear pulling up, or other noises, expectantly and dare not play any music or anything just incase I dont hear the bell.Re: Miele shock absorbers. Can they just go soft?
if there is a dollop of grease underneath them then yes they do go off. I have changed several, mainly at customers request and not had a call back yet.
Re: Belling IDW603 access to drain pump
Seamy wrote:Similar to a New World, think you have to take off side panel to get at it.
if only, both sides off and still unable to access it as its dead centre rear. Bottom is sealed as is rear. can only assume its a Bosch style top lot off the base job.
Re: Miele Tumble Dryer T7634?????????
not saying your wrong Don but every miele drier heater I ever order does not come with the saftey stat or ntc. Not in a position to check now but watch out, dont get caught out like I did the first time. Given the cost I expected it to come complete.
Usually a wiring diagram tucked under the lid.Re: 1607w rubber lip thing around door
kladave wrote:Hi Mark
got it back on with no probs at all and iirc went on the opposite to what you think it may go back on!!
Front stays on the machine but i removed the door assy.Dave
OK I admit, got it wrong, 😳 trying to fit it on the drum front plate instead of the cabinet front. went back today, with a new one and slipped it on as easy as anything. In my defence, on all the previous asko’s and ISE 10’s it does fit onto the drum front plate.
thanks Dave!
