[eastlmark]

Re: Miele G646 SC PLUS dishwasher flushing salt through

stuck re gen valve in rh side panel, can remove and clean but best to fit new. 5918860 is the part number.

[eastlmark]

Re: Football Season 2010/11

yes 2 very different games. think we were lucky though while the Arse were simply outplayed.
was uncomfortable viewing……

[eastlmark]

Re: Creda TCR2 Rubber Impeller

for £17 is it worth messing around?

[eastlmark]

Re: fisher paykel dishwasher

whiskey_six wrote:Not been out to one but the other engineers have said they are not nice. They have a technical helpline, just pretend to be an engineer working on behalf of an agent if they ask
0845 062 2300
😉

not true, possibly one of the easiest appliance to work on you will ever find.
F1 is a leak into base, would suspect first the fill hose has split to one of the draws, if so a new softner will be required as well. Other leak faults can be jammed draw lids or even just over dosing on detergent. Post the model and one of us will email you a service manual.

[eastlmark]

Re: Lux Stat

not sure what one it is but there are 2 listed
357 05 62-01/1 is described as a “stirrup thermostat” set
357 05 60-05/6 is described as “temperature regulator”.

[eastlmark]

Re: whirlpool awod 4605 859233316106 drum unit

johnmac11 wrote:Part number is 481241818744

John

bit slow there John, keep up mate! 😆

[eastlmark]

Re: maytag

try here: http://www.partadvantage.com/store

but without a model you are barking up a very tall tree.

[eastlmark]

Re: whirlpool awod 4605 859233316106 drum unit

481241818744

[eastlmark]

Re: New Bosch Free standing dish washer

I know the feeling, had to break away a bit of stuck on polystyrene to access the module on this one:
http://www.ukwhitegoods.co.uk/modules.p … ic&t=41254
Think the top half must come off in a similar way to the older model.

[eastlmark]

Re: Bosch Classix tumble dryer – low heat – WTE84104GB/17

plentyof parts info and availability here

I have had several with the same problem, you need a clamp meter to measure the current drawn and chances are it will be only around 3-4 amps while heating, it should be considerably more.
If this is the problem then it will be the power module behind the facia, take it out and out of its case and with any luck one of the heater relays will have a obvious dry solder joint on it. If not then it may be the relay contacts themselves, new board around £180 so probably BER if that is the case, worth looking at as I have had 3 with dry joints-dab of the iron and away they go.

[eastlmark]

Re: Smeg dual fuel oven SPA 42016?? Natural gas jet conversi

A42 is the model, all I have is a parts manual but would not know which parts you need.

[eastlmark]

Re: Hotpoint FF200EG defrost heater mod kit

iadom wrote:Check your PM’s 😉

Jim.

thanks Jim but not enough info, still need to know what to do with the heater.

[eastlmark]

Re: smeg diwi46.1

have emailed you something.

[eastlmark]

Re: Smeg slim line dishwasher dwf409 ss

funkyboogy wrote:hi mark – as per 1st post been checked ..

bit of a weird fault – good news is its an insurance job and a couple of parts are nla – yipee

NLA what? not that you really want to know! Sure we can get this going between us! 😉 Have you defo had that pump out?

[eastlmark]

Re: Smeg slim line dishwasher dwf409 ss

checked drain pumps not jammed? thats normally the first thing energised at start up.

[Author]

Posts