[electrofix]

Re: SMEG D16012 error not in instruction manual

if you read on it says a lot more

Dave

[electrofix]

Re: Beko American style fridge/ freezer GNEV320APS

have pm’ed you some info i found

Dave

[electrofix]

Re: SMEG D16012 error not in instruction manual

have you read this

http://www.ukwhitegoods.co.uk/help/faul … ing-lights

Dave

[electrofix]

Re: Bosch HTHB13 E-Nr HBN131560B not heating

“first make sure the clock is in manual mode is this just not flashing?” some clock will go in to manual mode when you reset them some wont. look to see if there is the word auto or an A in the display if yes the oven still wont function check your owners manual

“there are 2 plastic coupling pieces between the knobs and the switches and these break so switch cannot move “
turn the knob and watch the red switch on the left. make sure the switch moves as you turn the knob if yes its ok

if yes to the above its probably down to one of 2 things

1 the big red switch on the left has a failed contact
2 there is a safety thermostat that stop the oven if it gets too hot. it will be a small round unit with 2 wire on it screwed to the top or the back of the oven

if clock and couplings ok my bet is on the big switch but i cant be certain. if you remove it and turn it over you may see a burnt out contact

Dave

[electrofix]

Re: Bosch HTHB13 E-Nr HBN131560B not heating

first make sure the clock is in manual mode

there are 2 plastic coupling pieces between the knobs and the switches and these break so switch cannot move

check the multibank switch
there is also an overheat stat

Dave

[electrofix]

Re: Zanussi zwx 1506 all lights flashing

as long as it will start i cant think of anything

Dave

[electrofix]

Re: siemens sn66mo54gb

check the door hinges. the plastic hinge piece can move ( item 0552 on diags part no 165296) this lowers the door enough to cause problems

Dave

[electrofix]

Re: Zanussi zwx 1506 all lights flashing

E91 is a communication error between the 2 boards. being the control panel and the main power board
it can be as simple as a bad connection. find the connection wire between the 2 boards and unplug it and put it back 3 times to clean the contacts
then see how it goes

Dave

[electrofix]

Re: samsung WD8704 pump problem

thanks for your input

went out to panasonic like that but no switch on this one

went out again today checked all connections and put a volt meter on leads

its a board fault so customer is going to replace is as connect want £130 + vat +carr for the board

Dave

[electrofix]

Re: LG F1256QD tripping electrics after cycle completed

are you sure its the machine and not some other appliance?

check for leaks under the machine in case itva dampness problem

unplug machine to make sure its the problem ( ie if it still trips when its not plugged in it can be the machine)

Dave

[electrofix]

Re: Whirlpool 859204215010 heater replacement

cant confirm correct part number
looked in connect no heater listed
looked in Qualtex but had to search WWDC8420 gave no results if i added /2

Qualtex gave part number C00311143 against your number of C00312066

you need to double check as your number may well be correct for the /2 variant but have no whirlpool access

Dave

[electrofix]

Re: Miele W3830 Paragon Plus Tacho fault?

you will have to check both but first check the motor. its prob unlikely to be an open circuit coil so suspect magnet broken. if that ok check pcb Triac

Dave

[electrofix]

Re: Ikea/Electrolux Renlig DWT 160 3 beeps on starting.

part number

1527957128

looked in site shop its not listed but am sure they can order if reqd

Dave

[electrofix]

Re: samsung WD8704 pump problem

thanks maybe worth a revisit to check the leads because board not too cheap

Dave

[electrofix]

Re: LG front load WM WD8051C

if the motor brushes spark then it can cause the trips to go. Also suspect the heater if it trips on a wash programme
take each brush off the motor and see how long they are. New brushes are about 20mm long but they still work down to about 5mm.

Dave

[Author]

Posts