[electrofix]

Re: Hoover Nextra Dishwasher issue

most drain pump problems are down to an obstruction like glass or crockery jamming the impellor

you say you have checked the pump but have you opened it to check for the above

also the first thing any programme does is drain so does the pump run then ?

Dave

[electrofix]

Re: Hotpoint TVFS 73B

Key Lock
Prevents the program settings from being changed. After having selected the program and the available options, hold down the two
option buttons for 3 seconds (see “Dryer description”)
A prolonged beep will sound when the buttons are pressed and the LEDs on the options buttons will flash slowly twice. The LEDs
on the previously selected options will then remain lit but will no longer be modifiable.
If you attempt to change the settings with KEY LOCK activated, 3 short beeps will sound and 3 rapid flashes will warn you that it is
not possible to modify the program or the options underway.
Hold down the options buttons for three seconds to deactivate the KEY LOCK option. KEY LOCK can be selected with all programs.
The OFF position switches off the dryer.

maybe

Dave

[electrofix]

Re: overheated circuit board rangemaster

apart from its probably blown that board as well no idea

one of the problems with electronics is they hate surges and wires shorting out. it can pop chips a lot faster than any fuse can blow

Dave

[electrofix]

Re: Interlock on all spares sites looks different to origina

I looked it up and got the same thing but there are only 2 of these locks

3 pin and 4 pin so count the number of connections

for 3 terminal https://shop.ukwhitegoods.co.uk/catalog … t/?q=int43

for 4 terminal https://shop.ukwhitegoods.co.uk/catalog … t/?q=int42

Dave

[electrofix]

Re: Hotpoint FDEF 51110 F10 Error (Various symptoms)

no but most use a heater the is either part of the wash motor or in a tube leading into or out of the motor. either way its in the base

Dave

[electrofix]

Re: Leisure Laureat de luxe clock replacement

unless its still available you will struggle to replace it

Dave

[electrofix]

Re: Lg seal with out without tube ?

assume you are talking door seal

not sure what they mean but some lg seals have a pipe entering the top of the seal from a recirculating pump

Dave

[electrofix]

Re: Hotpoint FDEF 51110 F10 Error (Various symptoms)

well you have almost answered your own post

its a heat problem. the heater is not working so machine takes longer

there is a few things it could be but you need to find and test the heater first

Dave

[electrofix]

Re: Need a bit of help

difficult to be sure but it sounds like its overfilling

if you search for a local engineer on this site it will be a lot cheaper

Dave

[electrofix]

Re: Beko wmb81445lw

only the prod codes change they are both labelled eco

second machine is

prod code 7110843600

ECOWMB81445LW-1 Beko 8kg WM White

the manual is 6Mb don’t think I can pm that but if it is that one will try emailing it

Dave

[electrofix]

Re: Beko wmb81445lw

there are 2 machines with the same model

have pm’ed you the first one

prod code 7110842400

model DD WMB81445LW Beko 8kg 1400rpm

Dave

[electrofix]

Re: siemens topline washer dryer

the tacho small generator that generates an ac voltage

there are 6 or 7 pins on your motor which are as follows

2 pins armature
2 pins (or 3) field coil
2 pins tacho

first use a multimeter on low ohms scale and find which pins join to which pins. ie hold meter lead on first pin then move other lead down other pins till you get a reading. keep doing this till you can say what all pins do. the tacho coil may need a higher resistance scale to detect
the lowest ohm readings are the armature and field coil so ignore these pins. set meter to a low ac voltage scale (millivolts), put meter leads on the tacho output pins. spin motor and you should see an output.
if you get a signal it is important you check the voltage get to the board so buzz through the wiring harness to make sure you don’t have a broken wire

Dave

[electrofix]

Re: siemens topline washer dryer

by the look of it its a new rear end for the motor part number 496876 £58.86 from siemans

if it was this it sounds like the motor tacho is not working. the tacho is a magnet at the back of the motor armature that spins in a coil. it feeds a signal back to the electronics. make sure the magnet has not been damaged and check if there is an output with a multimeter

Dave

[electrofix]

Re: Looking for a part

to be honest you wont find one. as Ken said there is a similar unit in the hotpoint motor doing a similar job but cannot confirm its temperature rating. best to look for a secondhand motor on ebay or in you case a faulty one as long as the toc is ok

Dave

[electrofix]

Re: Wfb2005gb timer knob 155314

from what I can see you are right

but you can still get the whole panel including the knob but at about £150
there not going to sell many at that price which is why they have stock

Dave

[Author]

Posts