Forum Replies Created
-
Posts
-
Re: Britannia cooker hood lights stopped working
it is not easy to diagnose accurately but
the hum would be a transformer as I am assuming the lamps are a 12 volt halogen
therefore it could be
1 the transformer
2 the switch
3 the lampsDave
Re: bosch 1200 classixx express not heating water
NTC is the electronic thermostat normally its in a hole in the heater
other fault it can be is a bad solder joint on the main circuit board. all heaters are switched by relays on the board and they dont always solder correctly and fail
Dave
Re: John Lewis JLWM1203 drain pump error
no what martin means is play in the pump impellor (the white cross)
if you can hear thr pump trying to start then that is prob all it will be. if pump starts properly ( not just rattles) then you may have a blockage. i have had buttons half way down the outlet hose
Dave
Re: Kuppersbusch Oven Hinges
try this
http://tds.kueppersbusch-hausgeraete.de … log/index#
but its part of Teka and wow do they know how to charge for spares
Dave
Re: Neff V4380 Washer Dryer – Water not heating when drying
I agree when you rent the property the landlord is responsible for the appliances unless it is written into your contract that you are
also your problem has nothing to do with heating water. the tumble dryer section heats air that blows into the drum and heats the clothes to evaporate the water off them.
Re: Beko GNEV221APB
hi lawrence
not sure if you have access to beko tech but i have emailed all i can find to you web address
hope it helpsDave
Re: Smeg DWI710.E1 intermittant heating
you only need to change the large cap thats the power supply for the board
Dave
Re: Smeg DWI710.E1 intermittant heating
have you asked him what happens when it switches. if it switches and prog end shortly after that (ie pumps out and stops) I would assume error code
as for heater relays don’t rule out failure but also think about power supply problems (ie if voltage is low it may not be able to pull relay in sometimes )
hope it helps
Dave
Re: Bosch24364GB/05
well I don’t think much of your local repair man !!
from memory
plug machine in
turn prog dial to 6 oclock position
press and hold spin speed button
turn prog knob 1 click clockwise
release spin button
turn prog knob off wait 10 secs and turn back onyou may have to do it 3 or 4 times
Dave
Re: Zanussi TCE7124 (916092560/02) Condenser Dryer
if drum goes with a push but wont start otherwise most likely fault is motor capacitor
part no 1250020334
Dave
Re: hoover washing machine
from the owners manual from hoover site
Delay Start
This option allows you to delay the start of your wash cycle by up to 24 hours. By
pressing the Delay Start button, the time delay will be shown on the display (h00). This
will increase in one-hour intervals each time the Delay Start button is pressed.
Continue to press the button until the required time is reached, then press the Start
Pause button to activate the machine. The machine will start its cycle once the required
number of hours has passed.
To cancel the Delay Start option, press and hold the button for 5 seconds until the
display shows the settings for the selected programme. To start this programme, press
the Start Pause button. To cancel the process, turn the Programme Selector to the OFF
position and then select another programme.try this
Dave
Re: Limona built-in w/m (HJA 8513) no spin, erratic programm
common fault on these is the selector switch
part no 41014502
they are only cheap so worth a try
Dave
Re: Whirlpool/Maytag – Tumble Dryer Motor Glue
if it were me change the motor. you may be able to split it but getting it aligned again and getting a reliable joint could be a problem.
if you want to try I would use AralditeDave
Re: wiring on bosch oven!
I would pm Nomad if he is still around. He seems to have access to Bosch info
Dave
