[electrofix]

Re: Kenwood CK408 range only 1 ring working

found a wiring diag its on connect site

cooker is a fisher and paykel

and yes it has a 5 connection term block i would check that first

Dave

[electrofix]

Re: Kenwood CK408 range only 1 ring working

dont know the cooker but some hobs have links on the terminal blocks. if these have a bad connection it will stop some of the rings working

Dave

[electrofix]

Re: Hotpoint EW92 cooker stays hot when off

it will be the control behind the knob. simmerstat

Dave

[electrofix]

Re: baumatic BHD5 PCB

materpart list an ntc and got stock V75A000Y0

http://www.masterpart.com/default.aspx? … oupGuid=21

using part number qualtex have stock

BNTV75A000Y0

qualtex has no picture masterpart does but a google picture search on the partnumber V75A000Y0 brings it up

hope it helps

Dave

Dave

[electrofix]

Re: whirlpool adp2315

do you need to ?

is this not a quick way of checking the new element is working?

do they say why you have to use the test cycle ?

i would try it on a programme and see what happens. make sure it fills etc as if vno water comes in will blow new heater

Dave

[electrofix]

Re: Servis Quartz 1000 Deluxe, Model No.6027.

bril

glad to be of help

Dave

[electrofix]

Re: Hotpoint WM75 module

iadom wrote:Some of them do have a small, fast blow fuse in the wiring harness, some on the boards but that doesn’t explain the fact that it ran for a few seconds with no sign of a pop. 😕

make sense now i read it properly 😆

Dave

[electrofix]

Re: baumatic BHD5 PCB

have checked ntc wiring back to pcb ?

had one of these where the thermal limiter used to pop every now and then. i put it down to loading (ie if a plate was stopping water cooling area around stat it would trip )

ntc could be fault dont know resistance but would make it overheat if it was faulty. my answer would be one of 2 things 1 buy a new ntc 2 think resistance goes down with temp so put a 10k resistor across it and see what happens (this is meant as a test not a repair )

Dave

[electrofix]

Re: baumatic BHD5 PCB

what is the fault ?

Dave

[electrofix]

Re: Hotpoint WM75 module

not sure on this board but has it got a fuse for the motor ?

Dave

[electrofix]

Re: Zanussi ZDQ995X heating fault

have got wiring diag but no service manual

let me know if you want it

Dave

[electrofix]

Re: Homeking cooker Thermal cut out

try ringing qualtex they stock the cooker so should be able to source parts

dave

[electrofix]

Re: Servis Quartz 1000 Deluxe, Model No.6027.

still sound like a motor fault

i dont think the hotpoint motors are a straight swap for these. from memory think the tacho had a resistor across it on the plug and the motor pulley was different. check resistances from your old motor to see if things mactch

these motors always seemed to stuggle to start and i last saw one about 12 months ago. have just discarded 3 or 4 prog boards that i found in my attic. dont think i have anymore but will look

Dave

[electrofix]

Re: Zanussi ZDQ995X heating fault

with the conventional oven ok that would lead me to say the temp sensor is ok ( unless there are 2 sensors )
so it sound like your pcb
but

i would check the voltage on the element while it is running with a veiw to the following

1 element fails as it get hot long shot but you cant dismiss it till you have tried
2 relay that controls the element is faulty

am not in work at mo so i cant check if i have tech info on this. if its built before pm me will see what i have

Dave

[electrofix]

Re: BEKO WMP652W SPINS ON WASH

does it work ok at wash speeds ?

check you get tacho pulses to the pcb

can get tech info but may take me a few days as i am quite busy

let me have your email will see what i can do

Dave

[Author]

Posts