[electrofix]

Re: WHIRLPOOL 3LSC8255EQ1

never thought of that twist will try next time i get one

Dave

[electrofix]

Re: Hotpoint WD420G

if u look in known fault codes you get

light 3 & 4 flashes

f03 lights 3&4 Ntc fault

info is on site if you look around

hope this helps

Dave

[electrofix]

Re: zannussi w 1042 w

from the description it sounds like it thinks it is out of balance

was there washing in it when you tried some Zanussi units will not spin empty

Dave

[electrofix]

Re: WHIRLPOOL 3LSC8255EQ1

really simple to change this

if i am right you will need gearbox and spin clutch unit which is sat on top of box

as a quick guide

remove control panel screws slide forward and hinge it back

unplug wires to casing and remove clips holding casing in position tilt towards you and slide off

unclip pump, unplug motor , capacitor and earth wire remove clips and remove

take top off paddle in tub look down inside and remove plastic cover and remove bolt holding paddle. remove paddle under paddle there is somtimes a metal clip and washer remove

tilt machine at about 45 degree angle remove 3 bolts holding gearbox then lower box away

all you have to do is swop clutch and put back try not to turn tub if u do it will drop (not a lot ) and you will have to turn tub pushing up to be able to get box back in

Hope this helps

Dave

[electrofix]

Re: ZAN ZWF12170

any fault codes etc

if non could be pump triac short circuit in programmer

Dave

[electrofix]

Re: Zanussi ZWF1437w E34

e34 fault listed as

Inconsistency between level on electronic
pressure switch and level on anti-boiling pressure
switch 2 (fault persists for at least 60 sec.).

possible suggested cures

pressure switch defective;
Electrical current leak between heating element and ground; Heating
element; Wiring defective;
Main board defective.
Water circuit;

from lux disc

hope this helps

Dave

[electrofix]

Re: Zanussi ZJD1219

there are three of these machines need prod number to find which 1

are you getting a fault code coming up ?

as a long shot i assume the progammer knob is working and you are not selecting the same programme every time

regards

Dave

[electrofix]

Re: Zanussi TCS 675 EW Condensor T/D

is this with or without wet washing in as this is a sensor dryer

and you state it stops does it stop for a while then continue in the same direction ?

not in work till next week but couyld give you service manual if you pm me your email

Hope this helps
Dave

[electrofix]

Re: AEG Lavamat

should be part number 1100990355 water inlet compartment

should cost under £30 but could not be accurate

ring lux direct is the quickest way to get it on 01325 302464

hope this helps

Dave

[electrofix]

Re: philco pa207

thanks for offer of schematic have pm my email

@eastlmark

thought it was module till emw said it checks out ok have got a bit lost now without more wiring info

Dave

[electrofix]

Re: Hotpoint EW21C hotplate problem

not had this problem only thing i can think of is pans are they in full contact with ring
ie ring overheating in some places ?

hope this helps

Dave

[electrofix]

Re: Diplomat AWM8513 pulses?

this sounds like a timer problem

this is a long shot but have had a few machines where the power supply to the board is through a capacitor. as these age the voltage on the board goes down causing all sorts of problems

had a dishwasher the other week filled ok but as soon as motor kicked in it died ( just like a low battery )

check timer board to see how power is suppplied to board

hope this may help

Dave

[electrofix]

Re: Trade Spares

some of the trade list may not be trading now so you have to ring around

i use Qualtex their website is not as good as it could be but there has been small improvements but their call centre staff are first class.

hope this helps

Dave

[electrofix]

Re: Credaplan Europa Oven

have you check for power to the fan motor when it goes off

that would seal the problem does sound like the motor

Dave

[electrofix]

Re: Zanussi FLA1001W not heating

nts readings should be on early hybrid timers

30 degrees 17k
40 11.5k
50 7.8k
60 5.5k

i would put a straight resistor say 20k set to 50 degrees or higher and see if it heats

on late pcb units nts starts at

20 degrees 6k
60 degres 1250 ohms

also on some zanussi auto with pcb mounted in a box by rh suspension spring the timer is programmed to skip heat if no rise in temp is found within a set time. no fault code will appear. had one of the ended up new pcb now ok

hope this helps

Dave

[Author]

Posts